The Effect of Electrical Discharge Machining Parameters on Alloy DIN 1.2080 Using the Taguchi Method and Optimal Determinant

Journal of Simulation and Analysis of Novel Technologies in Mechanical Engineering

مقاله 1، دوره 8، شماره 2، مرداد 2015، صفحه 71-89   

نوع مقاله: Persian

نویسندگان

P. Sadr¹؛ Amin Kolahdooz^{* 2}؛ S.A. Eftekhari³

¹MSc. Student, Department of Mechanical Engineering, Islamic Azad University, Khomeinishahr Branch, Isfahan, Iran

²Assistant Professor, Young Researchers and Elite Club, Islamic Azad University, Khomeinishahr Branch, Isfahan/Khomeinishahr, Iran

³Assistant Prof., Department of Mechanical Engineering, Islamic Azad University, Khomeinishahr Branch, Isfahan, Iran.

چکیده

Electrical discharge machining process, is one of the most widely used methods for machining, the electrically conductive parts. In this way the tool is not in contact with the workpiece and the hardness of workpiece does not affect the machining speed. In Electrical Discharge Machining process, selection of the correct machining parameters are effective in final cost and the quality of the products. The special application of this alloy in various industries including tooling industry is attributed to its high hardness and wear resistance. The DIN 1.2080 steel at low temperature has a high wear resistance. Its hardness depth is high and it is suitable for machining at low temperature. In this paper, the effect of the type and setting parameters and determination of  optimal levels in of electrical discharge machining of alloy DIN 1.2080 using the Taguchi method and optimal determinant is examined The desired setting parameters including gap voltage, current intensity, on time and off time. The material removal rate and surface roughness of produced parts as the output characteristic of the study were investigated. Results showed that the spark current is more effective on the output parameter (more than 65% on material removal rate and more than 48% on a surface roughness), Other effective parameters are pulse on time, pulse off time and voltage changes, respectively. Higher current and pulse on time values and lower voltage and pulse off time values result in high MRR and low SR

کلیدواژه‌ها

Electrical Discharge؛ Machining؛ Taguchi؛ Optimal matrix؛ regression modeling؛ Optimization

مراجع

[1] Kalpakjian S, Manufacturing Engineering and Technology, Addison-Wesley, 1995.

[2] Uhlmann E., Domingosb D.C., Development and optimization of the die-sinking EDM technology for machining the nickel-based alloy MAR-M247 for turbine components, Procedia CIRP, Vol. 6, 2013, pp. 180 – 185.

[3] Ayestaa, Izquierdob B., Influence of EDM parameters on slot machining in C1023 aeronautical alloy, Procedia CIRP, Vol. 6, 2013, pp. 129 – 134.

[4] Gopakalannan S., Sinthelevan T., Modeling and Optimization of EDM Process parameter on Machining of AL 7075-B4 MMC using RSM, Procedia Engineering, Vol. 38, 2012, pp. 685 – 690.

[5] Clijsters S., Liu K., EDM technology and strategy development for the manufacturing of complex parts in SiSiC, Journal of Materials Processing Technology, Vol. 210, 2010, pp. 631–641.

[6] Tzeng Y.F., Development of a flexible high-speed EDM technology with geometrical transform optimization, journal of materials processing technology, Vol. 203, 2008, pp. 355–364.

[7] Rajmohan T., Prubho R., Optimization of Machining parameter in EDM of 304 Stainless Steel, Procedia Engineering, Vol. 38, 2012, pp. 1030 – 1036.

[8] Zarepour H., Fadaei Tehrani A., Statistical analysis on electrode wear in EDM of tool steel DIN 1.2714 used in forging dies, Journal of Materials Processing Technology, Vol. 187–188, 2007, pp. 708–714.

[9] Tzeng Y.F., Chen F., Multi-objective optimization of high-speed electrical discharge machining process using a Taguchi fuzzy-based approach, Materials and Design, Vol. 28, 2007, pp. 1159–1168.

[10] صابونی ح.ر.، بررسی پارامترهای ماشین‌کاری EDM با ابزار گرافیتی بر روی خواص مکانیکی آلیاژهای حافظ­دار NITI، دانشگاه آزاد اسلامی خمینی‌شهر، طرح پژوهشی ، 1391.

‫[11] عندلیب م.، ماشین‌کاری سوپر آلیاژ اینکونل 718 به روش تخلیه الکتریکی و بررسی تأثیر پارامترهای تنظیمی در کیفیت سطح و نرخ براده‌برداری قطعات تولیدی، پایان‌نامه ﮐﺎرﺷﻨﺎﺳﯽ ارﺷﺪ، ﮔﺮوه ﻣﮑﺎﻧﯿﮏ داﻧﺸﮕﺎه ﻓﺮدوﺳﯽ ﻣﺸﻬﺪ، (1392).

.2)/(2015 ,‪[12] www.esttoolsteel.com

 [13] Genichi Taguchi, Taguchi quality engineering handbook, New Jersey, 2005.

‪[14] www.minitab.com, 2015/3.

[15] Rajmohan T., Prubho R., optimization of Machining parameter in EDM of 304 Stainless Steel, Procedia Engineering, Vol. 38, 2012, pp. 1030 – 1036.

[16] ﺳﻤﭙﺮﯾﺖ، ﭼﺘﺮﺟﯽ، ﻋﻠﯽ اس، ﻫﺎدی و ﺑﺮﺗﺮام، ﭘﺮاﯾﺲ،  ﺗﺮﺟﻤﻪی دﮐﺘﺮ ﺣﺴﯿﻨﻌﻠﯽ ﻧﯿﺮوﻣﻨﺪ؛ ﺗﺤﻠﯿﻞ رﮔﺮﺳﯿﻮن ﺑﺎ ﻣﺜﺎل، انتشارات دانشگاه فردوسی مشهد، وﯾﺮاﯾﺶ ﺳﻮم، 1384.

[17] MINITAB 16.2.4 Manual, Minitab Inc., 2015.