Numerical Computation of Rolling Resistance Based on the Result of Tire/Road Static Contact Analysis

Journal of Simulation and Analysis of Novel Technologies in Mechanical Engineering

مقاله 4، دوره 8، شماره 3، آبان 2015، صفحه 185-196   

نوع مقاله: Persian

نویسندگان

H. Golbakhshi¹؛ M. Namjoo^{* 2}

¹- Lecturer, Department of Mechanical Engineering, University of Jiroft, 78671-61167, Jiroft, Iran

²- Lecturer, Department of Mechanical Engineering of Biosystems, University of Jiroft, 78671-61167, Jiroft, Iran.

چکیده

Among various dissipating mechanisms, the viscoelastic effect of rubber material on creation of rolling resistance is responsible for 10-33% dissipation of supplied power at the tire/road interaction surface. So, evaluating this kind of loss is very essential in any analysis concerned with improving the fuel consumption of vehicles and resultantly energy savage. Hysteretic loss is a fraction of stored strain energy of tire which is dissipated during the rotational motion. In all related references and published articles, the hysteretic loss per revolution of tire is commonly considered as the rolling resistance. However, a reasonable approximation of stresses and strains time histories is very crucial for evaluating the amount of hysteretic loss. Based on the results of 3D static contact analysis, an efficient in-house program coded in Matlab is used for estimating the time variation of stress-strain cycles at different points of a rolling tire. Half the difference between maximum and minimum principal values of six stress and strain components can be used for evaluating the hysteretic loss during one revolution of a rolling tire. The results closely match the related experimental and numerical investigations.

کلیدواژه‌ها

FE method؛ Rolling Resistance؛ Hysteretic loss؛ Numerical scheme

مراجع

[1] Cho J.R., Lee H.W., Jeong W.B., Jeong K.M., Kim K.W., Numerical estimation of rolling resistance and temperature distribution of 3-D periodic patterned tire, International Journal of Solids and Structures, vol. 50, No. 1, 2013, pp. 86-96.

[2] Hublau V., Barillier A., The Equations of the Rolling Resistance of a Tire Rolling on a Drum, Tire Science and Technology, vol. 36, No. 2, 2008, pp. 146-155.

[3] Pacejka H.B., Tyre and vehicle dynamics, Butterworth-Heinemann, ISBN 0-7506-5141-5, 2002.

[4] Wong J.Y., Theory of ground vehicles: Wiley.com, 2001.

[5] Mc Allen J., Cuitino A., Sernas V., Numerical investigation of the deformation characteristics and heat generation in pneumatic aircraft tires: Part II. Thermal modeling, Finite elements in analysis and design, vol. 23, No. 2, 1996, pp. 265-290.

[6] Ebbott T., Hohman R., Jeusette J.-P., Kerchman V., Tire temperature and rolling resistance prediction with finite element analysis, Tire Science and Technology, vol. 27, No. 1, 1999, pp. 2-21.

[7] Cho J., Kim K., Yoo W., Hong S., Mesh generation considering detailed tread blocks for reliable 3D tire analysis, Advances in engineering software, vol. 35, No. 2, 2004, pp. 105-113.

[8] Cho J., Kim K., Jeong H., Numerical investigation of tire standing wave using 3-D patterned tire model, Journal of sound and vibration, vol. 305, No. 4, 2007, pp. 795-807.

[9] Luchini J.R., Popio J.A., Modeling Transient Rolling Resistance of Tires 3, Tire Science and Technology, vol. 35, No. 2, 2007, pp. 118-140.

[10] Qi J., Herron J., Sansalone K., Mars W., Du Z., Snyman M., et al., Validation of a Steady-State Transport Analysis for Rolling Treaded Tires 5, Tire Science and Technology, vol. 35, No. 3, 2007, pp. 183-208.

[11] Ghoreishy M.H.R., A Numerical Study on the Non-linear Finite Element Analysis of a Tyre under Axisymmetric Loading, Iranian Polymer Journal, vol. 11, No. 5, 2002, pp. 325-332.

[12] Pillai P.S., Efect of tyre overload and inflation preasure on olling loss (resistance) and fuel consumption of automobile and truck/bus tires, Indian Journal of Engineering & Materaial Science, vol. 11, 2004, pp. 406-412.

[13] Lin Y.J., Hwang S.J., Temperature prediction of rolling tires by computer simulation, Mathematics and Computers in Simulation, vol. 67, No. 3, 2004, pp. 235-249.

[14] Ghoreishy M.H.R., A state of the art review of the finite element modelling of rolling tyres, Iranian Polymer Journal, vol. 17, No. 8, 2008, pp. 571-597.

[15] Korunović N., Trajanović M., Stojković M., Finite element model for steady-state rolling tire analysis, Journal of the Serbian Society for Computational Mechanics, vol. 1, No. 1, 2007, pp. 63-79.

[16] Kongo Kondé A., Rosu I., Lebon F., Brardo O., Devésa B., On the modeling of aircraft tire, Aerospace Science and Technology, vol. 27, No. 1, 2013, pp. 67-75.

[17] Li Y., Liu W., Frimpong S., Effect of ambient temperature on stress, deformation and temperature of dump truck tire, Engineering Failure Analysis, vol. 23, 2012, pp. 55-62.

[18] Shida Z., Koishi M., Kogure T., Kabe K., A rolling resistance simulation of tires using static finite element analysis, Tire Science and Technology, vol. 27, No. 2, 1999, pp. 84-105.

[19] Rao K.N., Kumar R.K., Bohara P., A sensitivity analysis of design attributes and operating conditions on tyre operating temperatures and rolling resistance using finite element analysis, Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering, vol. 220, No. 5, 2006, pp. 501-517.

[20] Park H., Youn S., Song T., Kim N., Analysis of temperature distribution in a rolling tire due to strain energy dissipation, Tire Science and Technology, vol. 25, No. 3, 1997, pp. 214-228.

[21] Oh B., Kim Y., Kim N., Moon H., Park H., Internal temperature distribution in a rolling tire, Tire Science and Technology, vol. 23, No. 1, 1995, pp. 11-25.

[22] Whicker D., Browne A.L., Segalman D.J. Structure and use of GMR combined thermo-mechanical tire power loss model. Society of Automotive Engineers, Inc., Warrendale, PA; 1981.

[23] Whicker D., Browne A., Segalman D., Wickliffe L., A thermomechanical approach to tire power loss modeling, Tire Science and Technology, vol. 9, No. 1, 1981,pp. 3-18.