Investigation of Cutting Forces Superalloy Inconel 718

Journal of Simulation and Analysis of Novel Technologies in Mechanical Engineering

مقاله 13، دوره 9، شماره 1 - شماره پیاپی 27، مرداد 2016، صفحه 181-186   

نوع مقاله: Persian

نویسندگان

Seyyed Masoud Badakhshian¹؛ Majid Karimian^{* 2}؛ Seyyed Ali Eftekhari³

¹Islamic Azad University, KHomeinishahr Branch

²Islamic Azad University, Khomeinishahr Branch

³Islamic Azad University. Khomeinishahr Branch

چکیده

Since the cutting tools used in machining process of super alloys are subjected to high cutting forces, accordingly tools life is reduced, therefore improvement in alloys machining and reducing cutting forces to achieve longer tools life is an essential necessity. In this research, the effect of changes in feed rate on cutting forces in machining process of nickel based super alloys is investigated. Cutting tools used in this experiment was a tungsten carbide material, model 890, geometry square shaped and specification of SNMG 120412. Also the tools has been coated using physical vapor deposition by chemical composition of TiN/TiCN/AlTiSiN in both micro and nano layer conditions. According to the results, as the feed rate is increased cutting forces mostly increases in both micro and nano layer coating conditions. . Generally in this research, application of micro layer coating results in less cutting forces compared to nano layer coating, so it can be said that micro layer coating has a better performance

کلیدواژه‌ها

Nickel Based Alloy؛ Cutting Tools؛ Cutting Forces؛ Feed Rate

مراجع

[1] Lee P., Altintas Y., “Prediction of Ball End Milling Forces from Orthogonal Cutting Data”, Int. J. of machine tools and manufacture, 36 1997, pp. 1059-1072.

[2] Choudhury I.A., E-Bardie M.A, “Machinability assessment of inconel 718 by factorial design of experiment coupled with response surface methodology”, Journal of Materials Processing Technology, 95, 1999, pp. 30-39.

[3] Darwish S.M., “The impact of the tool mterial and the cutting parameters on surface roughness of supermet 718 nickel superalloy”, Journal of Materials Processing Technology, 97, 2000, pp. 10-18.

[4] Li L., He N., Wang M., Wang Z.G., “High speed cutting of Inconel 718 with coated carbide and ceramic inserts”, Journal of Materials Processing Technology, 129, 2002, pp. 127-130.

[5] Coelho R.T., Silva L.R., Braghini Jr A., Bezzera A.A., “Some effects of cutting edge preparation and geometric modifications when turning Incoen 718 at high cutting speeds” Journal of Materials processing Technology, 148, 2004, pp. 147-153.

[6] Costes J.P., Guillet Y., Poulachon G., Dessoly M., “Tool-life and wear machanisms of CBN tools in machining of Inconel 718”, International Journal of Machine Tools and Manufacture, 47, 2000, pp. 1081-1087.

[7] Settineri L., Faga M.G., Lerga B., “Properties and performances of innovative coated tools for turning Inconel”, International Journal of Machine Tools and Manufacture, 48, 2007, pp. 815-823.

[8] Pawada R.S., Joushi S.S., Brahmankar P.K., Rahman M., “An investigation of cutting forces and surface damage in high-speed turning of Inconel 718”, Journal of Materials Processing Technology, 192-193, 2007, pp. 139-146.

[9] Nalbant M., Altin A., Gokkaya H., “The Effect of cutting tool geometry on machinability properties of nickel-base Inconel 718 super alloys”, Materials and Design, 28, 2007, pp. 1334-1338.

[10] Thakur D.G., Ramamoorthy B., Vijayaraghavn

        L., “Study on the machinability characterstics of superalloy Inconel 718 during high speed turning”, Materials and Design, 30, 2009, pp. 1718-1725.