New laboratory scale Grinding method to predict energy and the feed grindability of mill of Sarcheshmeh Copper Complex

Journal of Simulation and Analysis of Novel Technologies in Mechanical Engineering

مقاله 17، دوره 10، شماره 1 - شماره پیاپی 28، اردیبهشت 2017، صفحه 771-780   

نوع مقاله: Persian

نویسندگان

محمد رزانی^{* 1}؛ ابوالفضل معصومی²؛ مسعود رضایی زاده³؛ محمد نوع پرست⁴

¹عضو هیات علمی دانشگاه کار- دانشجویی دکتری مکانیک دانشگاه تهران

²عضو هیئت علمی دانشکده مهندسی مکانیک دانشگاه تهران

³عضو هیئت علمی بخش مکانیک دانشگاه تحصیلات تکمیلی و فن آوری پیشرفته کرمان

⁴عضو هیئت علمی دانشکده معدن دانشگاه تهران

چکیده

One of the factors which are usually difficult to be measured in mills is the grindability and distribution of feed under real situation and in a short time. In the condition of achieving a fast and convenient way to determine these parameters, the proper relationship between energy, hardness and particle size distribution can be obtained. Feed hardness is one of the most important factors in grinding of minerals in mineral-processing process, and this parameter depends on factors, such as the mechanical properties of minerals and collision conditions. The efficient use of energy during grinding of minerals in mills is one of the main objectives of this research. This research tried to provide an experimental method based on real collision conditions in a mill. Nowadays, SAG design test is used for evaluation of grinding circuit in the time of change in feed particle size distribution, size of the ball and the speed of mill, and for the prediction of energy required for complete grinding in AG and SAG mills. In this study, a new SAG design test for measuring the amount of specific energy and feed grindability was suggested and the effect of various parameters on product size distribution and hardness results was assessed. Results show the deviation of the A×b estimated by new method with values of drop weight tests were less than 1.9 percent. This new model can also be used to accurately predict the specific energy and particle size distribution..

کلیدواژه‌ها

Laboratory semi-autogenous؛ Energy Grindability؛ Particle size and Feed hardness

مراجع

[1] Bond F. C., Crushing and grinding calculations. Br. Chem. Eng. vol. 6, 1961, pp. 378–385.

[2] Amelunxen P., Berrios P., Rodriguez E., The SAG grindability index test. Miner. Eng. vol. 55, 2014, pp. 42–51.

[3] Bourgeois F. S., Banini G. A., A portable load cell for in-situ ore impact breakage testing. Int. J. Miner. Process, vol. 65, 2012, pp. 31–54.

[4] Abel F., Rosenkranz F. J., Kuyumcu H. Z., Stamped coal cakes in coke making technology Part 1— A parameter study on stampability. Iron Mak. Steelmak, vol. 65, 2009, pp. 321–326.

[5] Dobby G., Bennett C., Kosick G. Advances in SAG Circuit Design and Simulation Applied to the Mine Block Model. In Proceedings of the International Conference on Autogenous and Semi-Autogenous Grinding Technology, vol. 4, 2001, pp. 221–234.

[6] Bennett C., Dobby G. S., Kosick G., The keys to effective production forecasting and SAG circuit optimization,In Proceedings of the International Conference on Autogenous and Semi-Autogenous Grinding Technology, vol. 1, 2001, pp. 289–300, 2001.

[7] Kosick G., Dobby G., Bennett C., CEET (Comminution Economic Evaluation Tool) for Comminution Circuit Design and Production Planning. In Proceedings of 2001 SME Annual Meeting, Denver, CO, USA, 2001, pp. 26–28.

[8] Morrison R. D., Using DEM to model ore breakage within a pilot scale SAG mill, Minerals Engineering, vol. 17, 2004, pp. 1117–1124.

[9] Morrell S., Predicting the overall specific energy requirement of crushing, high pressure grinding roll and tumbling mill circuits, Minerals Engineering, vol. 22, 2009, pp. 544–549.

[10] Matthew D., Sinnott D., Is media shape important for grinding performance in stirred mills? Minerals Engineering, vol. 24, 2010, pp. 138–151.

[11] Powell M. S., Cleary W., Understanding fine ore breakage in a laboratory scale ball mill using DEM, Minerals Engineering, vol. 24, 2011, pp. 352–366.

 [12]        Morrell S., Predicting the specific energy of autogenous and semi-   autogenous mills from small diameter drill core samples, Minerals Engineering, vol. 17, 2003,  pp. 447–451.

[13]         Shi F., Comparison of grinding media – Cylpebs Verus Balls. Minerals Engineering, vol. 17, 2004, pp. 1259-1268.

[14]         Tavares L. M., Analysis of particle fracture by repeated stressing as damage accumulation. Powder Technology, vol. 190, 2009, pp. 327-339.

[15]         Khumalo N., Glasser D., Hildebrandt D., Hausberger B., Kauchali S., The application of the attainable region analysis to comminution. Chemical Engineering Science, vol. 61, 2006, pp. 5969–5980.

[16]         Barrios G., Carvalho R., Tavares L. M., Modeling breakage of monodispersed particles in unconfined beds. Minerals Engineering, vol. 24, 2011, pp. 308-318.

[17]         Genc O., Ergun S. L., Benzer A. H., Analysis of single particle impact breakage characteristics of raw and HPGR-crushed cement clinkers by drop weight testing. Powder Technology, vol. 25, 2014, pp. 37-45.

 [18] Napier-Munn T. J., Morrell S., Morrison R. D., Kojovic T., Mineral Comminution Circuits Their Operation and Optimisation, JKMRC Monograph Series, 1996.

[19] Rezaeizadeh M., Fooladi M M. Powell M. S., Weerasekara N. S., An experimental investigation of the effects of operating parameters on the wear of lifters in tumbling mills, Minerals Engineering, vol. 23, 2010, pp. 558-562.

[20] Tavares, L. M., Carvalho R., Guerrero J. C., Simulating the Bond rod mill grindability test. Miner. Eng. vol. 26, 2012, pp. 99–101.

[21] Razani M., Masomi M., Rezaeizadeh M., Investigation wear lifter impacts on SAG mill grindability using experimental and numerical methods. International Conference on research in science and technology, Malaysia, 2015.

[22] Tavares L.M., Carvalho R., Impact work index prediction from continuum damage model of particle fracture. Miner. Eng. vol. 20, 2007, pp. 1368–1375.