Process Parameters Optimization in Gas Blow Forming of Pin-type Metal Bipolar Plates using Taguchi and Finite Element Methods

ADMT Journal

مقاله 10، دوره 10، شماره 2، شهریور 2017، صفحه 101-108   

نویسندگان

M. Moradian¹؛ A. Doniavi^{* 1}؛ V. Modanloo²؛ V. Alimirzaloo¹

¹Department of Mechanical Engineering, University of Urmia, Iran

²Young Researchers and Elite Club, Urmia Branch, Islamic Azad University, Urmia, Iran

چکیده

Metal bipolar plates are the most important parts of the fuel cells and recently these plates are used instead of graphite ones.In the present study, gas blow forming of a pin-type aluminum 5083 bipolar plate has been studied. After the simulation of the process, the FE model has been validated using experimental results. Then, the effects of parameters including maximum pressure of the gas, pressurization profile and corner radius of the pin on thinning ratio and forming depth of final part have been investigated. Nine experiments were designed using the Taguchi L9 orthogonal array and the experiments were performed using the FE model. The signal to noise (S/N) ratio and the analysis of variance (ANOVA) techniques were carried out to determine the effective parameters and the contribution of each parameter. The maximum pressure of 1.2 MPa, SP2 pressurization profile and corner radius of 0.2 mm lead to the minimum thinning ratio. Also, it was found that to maximize the forming depth, the maximum pressure of 2 MPa, SP1 pressurization profile and corner radius of 0.3 mm should be selected. Also, ANOVA analysis showed that the most significant parameters on thinning ratio and forming depth are corner radius and maximum pressure, respectively.

کلیدواژه‌ها

Bipolar plate؛ Finite Element Simulation؛ Gas blow forming؛ Process parameters

مراجع

[1]       Middelman, E., Kout, W., Vogelaar, V., Lenssen, J., and Waal, E.; “Bipolar Plates for PEM Fuel Cells”, Journal of Power Sources, Vol. 118, No. 1-2, 2003, pp. 44-46.

[2]       Mahabunphachai, S.; “A Hybrid Hydroforming and Mechanical Bonding Process for Fuel Cell Bipolar Plates”, PhD. Dissertation, University of Michigan, 2008.

[3]       Heinzel, A., Mahlendorf, F., and Jansen, C., Bipolar Plates, Elsevier, Duisburg, 2009.

[4]       Wang, H. L., Sweikart, M. A., and Turner, J. A.; “Stainless Steel as Bipolar Plate Material for Polymer Electrolyte Membrane Fuel Cells”, Journal of Power Sources, Vol. 115, No. 2, 2003, pp. 243-251.

[5]       Elyasi, M., Khatir, F.A., and Hosseinzadeh, M.; “Manufacturing Metallic Bipolar Plate Fuel Cells Through Rubber Pad Forming Process”, The International Journal of Advanced Manufacturing Technology, 2016, pp. 1-13.

[6]       Belali Owsia, M., Hosseinipour, S. J., Bakhshi-Jooybari, M., and Gorji, A.; “The Experimental and Simulation Investigation of Process and Geometrical Parameters for Hydroforming of Pin-type Metallic Bipolar Plates”, Modares Mechanical Engineering, Vol. 15, No. 7, 2015, pp. 215-226.

[7]       Mohammadtabar, N., Bakhshi-Jooybari, M., and Hosseinipour, S.J.; “Study of Effective Parameters in Hydroforming of Fuel Cell Metallic Bipolar Plates with Parallel Serpentine Flow Field”, Modares Mechanical Engineering, Vol. 14, No. 8, 2014, pp. 17-27.

[8]       Shamsi-Sarband, A., Hosseinipour, S. J., Bakhshi-Jooybari, M., and Shakeri, M.; “The Effect of Geometric Parameters of Conical Cups on the Preform Shape in Two-Stage Superplastic Forming Process”, Journal of Materials Engineering and Performance, Vol. 22, No. 12, 2013, pp. 3601-3611.

[9]       Sun, P., Wu, H., Tsai, H., Huang, C., and Tzou, M.; “Effect of Pressurization Profile on the Deformation Characteristics of Fine-grained AZ31B Mg Alloy Sheet During Gas Blow Forming”, Journal of Materials Processing Technology, Vol. 210, 2010, pp. 1673-1679.

[10]    Esmaeili, S., Hosseinipour, S. J., Shamsi-Sarband, S.; “Simulation and Experimental of Metallic Bipolar Plates for Fuel Cell by Gas Blow Forming Process”, National conference on Mechanical Engineering, Malayer, Iran, 2013.

[11]    Kadkhodayan, M., Pourhasan, P.; “Finite Element Simulation of Process and Springback of Friction Aided Deep Drawing Using Tapered Blank Holder Divided Into Eight Segments”, International Journal advanced Design and Manufacturing Technology, Vol. 3, No. 4, 2010, pp. 1-10.

[12]    Alimirzaloo, V., Modanloo, V; “Minimization of the Sheet Thinning in Hydraulic Deep Drawing Process Using Response Surface Methodology and Finite Element Method”, International Journal of Engineering (IJE), Transactions B: Applications, Vol. 29, No.2, 2016, pp. 264-273.

[13]    Modanloo, V., Gorji, A., and Bakhshi-Jooybari, M.; “Effects of Forming Media on Hydrodynamic Deep Drawing”, Journal of Mechanical Science and Technology, Vol. 30, No. 5, 2016, pp. 2237-2242.

[14]    Kolahdoozan, M., Azimifar, F., and Yazdi, S. R.; “Finite Element Investigation and Optimization of Tool Wear in Drilling Process of Difficultto-Cut Nickel-Based Superalloy using Response Surface Methodology”, International Journal Advanced Design and Manufacturing Technology, Vol. 7, No. 2, 2014, pp. 67-75.

[15]    Modanloo, V., Hasanzadeh, R. and Esmaili, P.; “The Study of Deep Drawing of Brass-steel Laminated Sheet Composite Using Taguchi Method”, International Journal of Engineering (IJE), Transactions A: Basics, Vol. 29, No.1, 2016, pp. 103-108.