Synthesis and application of the drilling mud additive in the presence of surfactants

International Journal of Nano Dimension

مقاله 7، دوره 7، شماره 4، اسفند 2016، صفحه 321-328   

نوع مقاله: Reasearch Paper

شناسه دیجیتال (DOI): 10.7508/ijnd.2016.04.007

نویسندگان

Mehran Sadeghalvaad^{1، 2}؛ Samad Sabbaghi^{* 1}؛ Pooneh Afsharimoghadam^{1، 3}

¹Faculty of Advanced Technology, Nano Chemical Engineering Department, Shiraz University, Shiraz, Iran.

²Nano Chemical Engineering Department, Radin Faradid Petro Sanat Co., Fars Science and Technology Park, Shiraz, Iran.

³Department of Earth Sciences, College of Science, Shiraz University, Shiraz, Iran.

چکیده

Drilling fluid is the most important lifeline of the drilling operation, that main task is facilitate the cuttings removal of the drilling. There are varieties of drilling fluids such as sodium bentonite based-drilling fluid is called “mud” and drilling foam or surfactant based-drilling fluid is called “soap”. The present work aims are study on the modified drilling mud properties by using the TiO2/ Polyacrylamide (PAM) as a nanocomposite additive. This additive was obtained through the aqueous solution polymerization of acrylamide monomer in the presence of TiO2 nanoparticles and high hydrophilic-lipophilic balance (HLB) surfactants such as sodium dodecyl sulfate (SDS) and polyoxyethylene sorbitan mono-oleate (Tween 80). At first, the TiO2/PAM nanocomposite was characterized by XRD, UV-Vis, FTIR, DLS and SEM. Then the viscosity, density -specific gravity- and filtration properties of the modified drilling mud were investigated in different amount of nanocomposite compounds. The results indicated that the density, fluid loss and filter cake thickness of the modified drilling mud were decreased with the increase of the surfactant concentration, whereas the viscosity was increased. With the increasing amount of SDS from 0.1 to 1.2 g in the synthesis process, the viscosity was increased approximately 4 cP and the density was decreased about 0.1 specific gravity. The nanoparticle and HLB value were affected in the filtration properties, but in general, that improved the fluid loss and filter cake thickness about 28 and 38% compared the based drilling mud, respectively.

کلیدواژه‌ها

Drilling mud؛ Nanocomposite؛ Polyacrylamide؛ surfactant؛ TiO2

مراجع

[1] World Oil 2004 Drilling, (2004), Completion and Work over Fluids. World Oil. 225: 1-6.

[2] Berthezene N., Hemptinne J., Audibert A., Argillier J., (1999), Methane solubility in synthetic oil-based drilling muds. J. Petrol. Sci. Eng. 23: 71–81.

[3] Garcia-Ochoa F., Santos V. E., Casas J. A., Gomez E., (2000), Xanthan gum: Production, recovery, and properties. Biotechnol. Adv. 18: 549-579.

[4] Pérez R. M., Siquier S., Ramı́rez N., Müller A. J., Sáez A. E., (2004), Non-Newtonian annular vertical flow of sand suspensions in aqueous solutions of guar gum. J. Petrol. Sci. Eng. 44: 317–331.

[5] Caenn R., Chillingar G. V., (1996), Drilling fluids: State of the art. J. Petrol. Sci. Eng. 14: 221–230.

[6] Dolz M., Jiménez J., Hernández M. J., Delegido J., Casanovas A., (2007), Flow and thixotropy of non-contaminating oil drilling fluids formulated with bentonite and sodium carboxymethyl cellulose. J. Petrol. Sci. Eng. 57: 294-302.

[7] Kok M. V., Iscan G., (2009), Effect of Carboxy Methyl Cellulose and Determination of Pore Throat Criteria for Water-based Drilling Fluids. Energy Sources Part A: Recovery Utilization Environ. Eff. 31: 396–405.

[8] Dairanieh I. S., Lahalih S. M., (1988), Novel polymeric drilling mud viscosifiers. Eur. Polym. J. 24: 831-835.

[9] Paiaman A. M., Al-Anazi D. B., (2009), Feasibility of decreasing pipe sticking probability using nanoparticles. NAFTA 60: 645-647.

[10] Abdo J., Haneef M. D., (2013), Clay nanoparticles modified drilling fluids for drilling of deep hydrocarbon wells. Appl. Clay. Sci. 86: 76-82.

[11] Fereydouni M., Sabbaghi S., Saboori R., Zeinali S., (2012), Effect of polyanionic cellulose polymer nanoparticles on rheological properties of drilling mud. Int. J.  Nanosci. Nanotech. 8: 171-174.

[12] Saboori R., Sabbaghi S., Mowla D., Soltani A., (2012), Decreasing of water loss and mud cake thickness by CMC nanoparticles in mud drilling. Int. J. Nano Dimens. 3: 101-104.

[13] Luo Y. R., Chen M., Liu D. S., Jin Y., Du M. H., Hou J., (2012), Technology and applications of foam drilling fuid in fractured and complex formations. Petrol. Sci. Technol. 30: 1747-1754.

[14] Herzhaft B., Toure A., Bruni F., Saintpere S., (2000), Aqueous foams for underbalanced drilling: The question of solids. SPE 62898, Presented at the 2000 SPE Annual Technical Conference and Exhibition, Dallas, Texas, October 1-4.

[15] Rojas Y., Vieira P.,  Borrell M.,  Blanco J. , Ford M., Nieto L., Lopez G., Atencio B., (2002), Field application of near-balanced drilling using aqueous foams in western venezuelapaper. IADC/SPE 74449 presented at the 2002 IADC/SPE drilling conference, Dallas, Texas, February 26-28.

[16] Ozbayoglu E. M., (2009), Pressure loss at the bit while drilling with foam. Petrol. Sci. Technol. 27: 687-698.

[17] Dong-mei W., Da-kuang H., Guan-li X., Li Y., (2008), Influence of partially hydrolyzed polyacrylamide on the foam capability of α-Olefin Sulfonate surfactant. Petrol. Explor. Develop. 35: 335-338.

[18] Alizadeh S., Sabbaghi S., Soleymani M., (2015), Synthesis of Alumina/Polyacrylamide nanocomposite and its influence on viscosity of drilling fluid. Int. J. Nano Dimens. 6: 271-276.

[19] Sadeghalvaad M., Sabbaghi S., (2015), The effect of the TiO2/polyacrylamide nanocomposite on water-based drilling fluid properties. Powder Technol. 272: 113-119.

[20] Sadeghalvaad M., Sabbaghi S., (2015), The preparation and rheological studies of the TiO2/Polyacrylamide nanofluid. J. Nanofluids. 4: 435-441.

[21] Zhang D., (2012), Improved visible light photocatalytic activity of Titania loaded with Silver on discoloration of a heterocyclic aromatic chemical dye solution. Russ. J. Phys. Chem. A. 86: 675-680.

[22] Gadhave A., (2014), Determination of hydrophilic-lipophilic balance value.  Int. J. Sci. Res. 3: 573-575.