Fully HF Welded Helical Finned Tubes in Combined Cycle Power Plant

Journal of Environmental Friendly Materials

مقاله 8، دوره 3، شماره 2 - شماره پیاپی 6، اسفند 2019، صفحه 41-47   

نوع مقاله: Technical Article

نویسندگان

M. Sadeghi¹؛ H. Sabet¹؛ H. Razavi²

¹Department of Materials Engineering, Karaj Branch, Islamic Azad University, Karaj, Iran

²Department of Materials Engineering, Iran University of Science & Technology, Tehran, Iran

چکیده

Environment friendly industrial fin tube boilerused a heat recovery system generator (HRSG) is the core facility of a combined cycle power plant (CCPP) that recycles thermal energy from a gas turbine and creates high temperature and high pressure gas. Serrated finned tubes and solid finned tubes are two types of helically finned tubes made by high-frequency resistance welded (HFRW). Solid and serrated fins are widely consumed solutions for improving heat transfer in fired heaters. The important fact that designers or engineers often overlook while selecting the fins is that serrated fins can provide larger surface area and significantly higher fin efficiency compared with solid fins. Carbon steel and alloy steel tube according to ASTM A192 and ASTM A213. As well as carbon steel and alloy steel coil strips according to ASTM A1008 and ASTM A240-TP409. International standard for tests of high frequency resistance welded fins according ASME and ASTM used for metallography fusion weld, tensile strength and hardness. This paper presents the microstructures welding of helically fin tube boiler, with particular emphasis on HFRW.

مراجع

[1] V. Eriksen, Heat Recovery Steam Generator Technology, Woodhead Publishing, (2017).

[2] Eugene, Pis’mennyi, Georgiy Polupan, Ignacio, Carvajal-Mariscal, Florencio, Sanchez-Silva, Igor Pioro, Handbook for Transversely Finned Tube Heat Exchanger Design Academic Press, (2016).

[3] M. Więcek: Wpływ Technologii Spawania na Strukturę I Właściwości Nur Ożebrowanych Dla Przemysłu Energetycznego. PhD Thesis, Po- Litechnika Śląska, Wydział Inżynierii Materiałowej I Metalurgii, (2015).

[4] P. Breeze: Raising Steam Plant Efficiency– Pushing the Steam Cycle Boundaries. PEI Magazine, (2012), 20.

[5] R. Huseman: Advanced (700°C) PF Power Plant. A Clean Coal European Technology. Advanced Material for AD700 Boilers, Cesi Auditorium, Milano, (2010).

[6] J. Mitrovic: Heat Exchanger and Condenser Tubes, Tube Types – Materials – Attributes – Machning. Publico Publications, (2004).

[7] Z. Dziemidowicz, P. Szyszka and I. Krupa: Power Units on the Horizon. The Technical Requirements ofNew Generation Units at PGE Power Plant Opole S. A. Electric Heat and Vocational Education (2011).,11

[8] R. Kocurek, J. Adamiec, Adv. Mater. Sci., (2013) , 13 .

[9] Erling Næss, Experimental investigation of heat transfer and pressure drop in serrated-fin tube, Applied Thermal Engineering 30, 1531e1537,(2010).

[10] J. Noordermeer, P. Eng., IAGT Symposium, Training Sessions, BANFF, ALBERTA, (2013).

[11] ASTM A240 Standard Specification for Heat Resisting Chromium and Chromium-Nickel Stainless Steel Strip for Pressure Vessels, (2018).

[12] ASTM A213 Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler,  Superheater, and Heat-Exchanger Tubes, ( 2018).

[13] ASTM E340-18, Standard Test Method for Macro Etching Metals and Alloys, (2018).

[14] ASTM A370-18, Standard Test Methods and Definitions for Mechanical Testing of Steel Products,  (2018).

[15] ASTM E384-18, Standard Test Method for Micro indentation Hardness of Materials, ( 2018).