Investigation and Comparison of Microstructure and Mechanical Properties Between Parts of Shear Spinning and Rolled

Journal of Environmental Friendly Materials

مقاله 2، دوره 5، شماره 2 - شماره پیاپی 10، اسفند 2021، صفحه 1-9   

نوع مقاله: Original Article

نویسندگان

H Ghayour¹؛ S. M. J Hoseini¹؛ A Salemi Golezani²؛ M. K Asgarani¹؛ I Ebrahimzadeh¹

¹Advanced Materials Research Center, Department of Materials Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Iran

²Advanced Materials Engineering Research Center, Karaj Branch, Islamic Azad University, Karaj, Iran

چکیده

In this study, the shear spinning process and the rolling process on C11000 copper metal with a thickness reduction of 50% at room temperature were performed and investigated. In the shear spinning specimen, the grains are stretched in the axis direction and elongated in the circumferential direction. In the rolled specimen, the grains are extended in the direction of rolling, and the elongation of the grains in the T-N plane is less than in the shear spinning specimen. EBSD analysis showed that the ratio of high angle boundaries to low angle boundaries in the shear spinning specimen is higher than the rolled specimen. The mechanical properties of the rolled and shear spinning specimens were investigated in three directions of zero, 45, and 90 degrees relative to the forming direction, which showed that the strength in all three directions was higher in the rolled specimen than in the shear spinning specimen. The elongation in the shear spinning specimen is more than in the rolled specimen. The highest amount of tensile strength in the rolled specimen is about 370 MPa, and the highest elongation is about 12% in the shear spinning specimen. Also, anisotropy in shear spinning specimens was less than rolled specimens.
 

کلیدواژه‌ها

Spinning؛ Shear Spinning؛ Rolling؛ Mechanical Properties؛ Copper

مراجع

[1] J. R. Davis, S. D. Henry, B. R. Sanders, N. Hrivnak, J. A. Kinson and W. W. Scott, ASM Specialty Handbook, Copper and Copper Alloys, ASM International, (2001), 3.

[2] Z. Yanushkevich, A. Belyakov, R. Kaibyshev, C. Haase and D. A. Molodov, Deformation and Recrystallization Textures in a High-Mn Steel Subjected to Large Strain Cold Rolling, Proc. Int. Conf. Recrystallization Grain Growth (ReX&GG 2016), Pittsburgh, USA, (2016).

[3] P. Pawar, A. Pagar, A. Shah and S. Yevale, Review on Spinning Attachment to Lathe Machine, Int. Conf. on Ideas, Impact and Innovation in Mech. Eng., (ICIIIME 2017).

[4] L. Radović, M. Nikačević and B. Jordović, Trans. Nonferrous Met. Soc. China, 22, (2012), 991.

[5] C. C. Wong, T. Dean and J. Lin, Rev. , Int. J. Mach. Tools Manuf., 43, (2003), 1419.

[6] E. Hagan and J. Jeswiet, Rev. Proc. Inst. Mech. Eng. B, 217, (2003), 213.

[7] W. F. Hosford and R. M. Caddell, METAL FORMING: Mechanics and Metallurgy, Third Edition, Cambridge University Press, (2007).

[8] M. Sivanandini, S. Dhami and B. Pabla, Flow Forming Of Tubes-A Review, IJSER, 3(2012), 1.

[9] M. Zhan, X. Wang and H. Long, Mater. Des., 108, (2016), 207.

[10] X. Wang, M. Zhan, M. Fu, J. Guo, R. Q. Xu, X. P. Lei, Procedia Engineering, 207, (2017), 1725.

[11] M. Guillot, T. McCormack, M. Tuffs, A. Rosochowsk, S.Halliday and P. Blackwell, Procedia Eng., 207, (2017), 1719.

[12] Q. Liu and N. Hansen, Proc. R. Soc. Lond. A, 454, (1998), 2555.

[13] Y. Xu, H. Jiao, W. Qiu, R. D. K. Misra and J. Li, Mater., 1161, (2018), 1.

[14] X. Wang, P. Gao, M. Zhan, K. Yang, Y. Dong and Y. Li, Chinese J. Aeronaut., 33, (2020), 2088.

[15] C. Kubilay, Writer, Flow Forming Of Aeroengine Materials. [Performance]. Ph.D. Thesis Submitted in the University of Manchester, (2014).

[16] T. T. B. Wardoyo, S. Izman and D. Kurniawan, Appl. Mech. Mater., 315, (2013), 739.

[17] C. Deng, S. F. Liu, J. L. Ji, X. B. Hao, Z. Zhang and Q. Liu, J. Mater. Process. Technol., 214, (2014), 462.

[18] M. Haghshenas and R. J. Klassen, Mater. Sci. Eng. A, 641, (2015), 249.

[19] T. Sakai, A. Belyakov, R. Kaibyshev, H. Miura and J. Jonas, Prog. Mater. Sci., 60, (2014), 130.

[20] M. Bacca, D. Hayhurst and M. R. McMeeking, Mech. Mater., 90, (2015), 148.

[21] F. Humphreys and M. Hatherly, Recrystallization and related annealing phenomena, 2 ed., Oxford: Elsevier, (2004), 11.

[22] H. Zhao, S. Ni, M. Song, X. Xiong, X. Liang and H. Li, Mater. Sci. Eng. A, 645, (2015), 328.

[23] Q. Xia, G. Xiao, H. Long, X. Cheng and B. Yang, Mater. Des., 59, (2014), 16.

[24] W. Xu, D. Shan, Z. Wang, G. Yang, Y. Lu and D. Kang, Trans. Nonferrous Met. Soc. China, 7, (2007), 1205.