Distraction Osteogenesis in Oral and Maxillofacial Reconstruction Applications: Feasibility Study of Design and Development of an Automatic Continuous Distractor

Majlesi Journal of Electrical Engineering

مقاله 9، دوره 12، شماره 3، آذر 2018، صفحه 69-75   

نوع مقاله: Review Article

نویسندگان

Katayoun Hatefi^{* 1}؛ Shahrokh Hatefi²؛ Milad Etemadi³

¹Department of Electrical and Computer Engineering, Isfahan University of Technology, Isfahan

²Department of Mechatronics, Nelson Mandela University

³Department of Oral and Maxillofacial Surgery, School of Dentistry, Isfahan University of Medical Sciences, Isfahan

چکیده

Distraction Osteogenesis (DO) is one of novel techniques widely used in bone Reconstruction Applications (RA). Recently, DO method has got an important role in oral and maxillofacial RA; by using DO bone defects and skeletal deformities in different cranio-maxillofacial areas can be reconstructed, with better results and reduced effects in comparison to conventional methods. In DO by using a tension-stress principle, mechanical stimulations induce bone generation and biological responses of the tissue. A DO procedure starts with bone osteotomy and implementation of distractor, before proceeding with distraction, there is a latency period which allows the callus to form initially. In the distraction phase, the generated external force goes through the moving bone segment and gradually distract the callus. After distraction phase, there is a consolidation phase and then the device is removed. Most of current DO methods are applied by manual devices; low accuracy and reliability, discontinuous force, manually-operated, and associated problems for patient are major disadvantages of manual devices. Recent studies have revealed using an automatic continuous distractor could significantly improve the DO results while decreasing the existing problems. The purpose of this study is to design and simulate a novel automatic continuous distractor to be used in DO applications. The device contains mini stepper motor and gear-box, controller, mechatronic system, LCD, and keypad. Design’s specification and simulations results show this device has the capability to generate a continuous distraction force for a successful automatic DO.

کلیدواژه‌ها

Automatic Continuous Controller؛ Distraction Osteogenesis؛ Medical Devices

مراجع

[1] 1. Amir, L.R., V. Everts, and A.L. Bronckers, Bone regeneration during distraction osteogenesis. Odontology, 2009. 97(2): p. 63-75.

[2] 2. Ilizarov, G.A., The tension-stress effect on the genesis and growth of tissues: Part I. The influence of stability of fixation and soft-tissue preservation. Clinical orthopaedics and related research, 1989. 238: p. 249-281.

[3] 3. Ilizarov, G.A., The tension-stress effect on the genesis and growth of tissues: Part II. The influence of the rate and frequency of distraction. Clinical orthopaedics and related research, 1989. 239: p. 263-285.

[4] 4. Cano, J., et al., Osteogenic alveolar distraction: a review of the literature. Oral Surgery, Oral Medicine, Oral Pathology, Oral Radiology, and Endodontology, 2006. 101(1): p. 11-28.

[5] 5. Mandible distraction osteogenesis. 2017; Available from: https://www.aofoundation.org/Structure/Pages/default.aspx.

[6] 6. Snyder, C.C., et al., Mandibular lengthening by gradual distraction: preliminary report. Plastic and reconstructive surgery, 1973. 51(5): p. 506-508.

[7] 7. Karp, N.S., et al., Bone lengthening in the craniofacial skeleton. Annals of plastic surgery, 1990. 24(3): p. 231-237.

[8] 8. McCarthy, J.G., et al., Lengthening the human mandible by gradual distraction. Plastic and reconstructive surgery, 1992. 89(1): p. 1-8.

[9] 9. Zhou, H.-Z., et al., Rapid lengthening of rabbit mandibular ramus by using nitinol spring: a preliminary study. Journal of Craniofacial Surgery, 2004. 15(5): p. 725-729.

[10] 10. Kojimoto, H., et al., Bone lengthening in rabbits by callus distraction. The role of periosteum and endosteum. Bone & Joint Journal, 1988. 70(4): p. 543-549.

[11] 11. Paley, D., et al., Treatment of congenital pseudoarthrosis of the tibia using the Ilizarov technique. Clinical orthopaedics and related research, 1992. 280: p. 81-93.

[12] 12. Dzhorov, A. and I. Dzhorova, Maxillofacial surgery and distraction osteogenesis--history, present, perspective. Khirurgiia, 2002. 59(6): p. 30-35.

[13] 13. Karp, N.S., et al., Membranous bone lengthening: a serial histological study. Annals of plastic surgery, 1992. 29(1): p. 2-7.

[14] 14. Zheng, L., et al., High-rhythm automatic driver for bone traction: an experimental study in rabbits. International journal of oral and maxillofacial surgery, 2008. 37(8): p. 736-740.

[15] 15. Mehrara, B.J., et al., Rat mandibular distraction osteogenesis: II. Molecular analysis of transforming growth factor beta-1 and osteocalcin gene expression. Plastic and reconstructive surgery, 1999. 103(2): p. 536-547.

[16] 16. Rowe, N.M., et al., Rat mandibular distraction osteogenesis: Part I. Histologic and radiographic analysis. Plastic and reconstructive surgery, 1998. 102(6): p. 2022-2032.

[17] 17. Kessler, P., F. Neukam, and J. Wiltfang, Effects of distraction forces and frequency of distraction on bony regeneration. British Journal of Oral and Maxillofacial Surgery, 2005. 43(5): p. 392-398.

[18] 18. Wiltfang, J., et al., Continuous and intermittent bone distraction using a microhydraulic cylinder: an experimental study in minipigs. British Journal of Oral and Maxillofacial Surgery, 2001. 39(1): p. 2-7.

[19] 19. Peacock, Z.S., et al., Automated continuous distraction osteogenesis may allow faster distraction rates: A preliminary study. Journal of Oral and Maxillofacial Surgery, 2013. 71(6): p. 1073-1084.

[20] 20. Peacock, Z.S., et al., Bilateral Continuous Automated Distraction Osteogenesis: Proof of Principle. The Journal of craniofacial surgery, 2015. 26(8): p. 2320-2324.

[21] 21. Peacock, Z.S., et al., Skeletal and soft tissue response to automated, continuous, curvilinear distraction osteogenesis. Journal of Oral and Maxillofacial Surgery, 2014. 72(9): p. 1773-1787.

[22] 22. Djasim, U.M., et al., Continuous versus discontinuous distraction: evaluation of bone regenerate following various rhythms of distraction. Journal of Oral and Maxillofacial Surgery, 2009. 67(4): p. 818-826.

[23] 23. Mofid, M.M., et al., Callus stimulation in distraction osteogenesis. Plastic and reconstructive surgery, 2002. 109(5): p. 1621-1628.

[24] 24. Zheng, L.W., L. Ma, and L.K. Cheung, Angiogenesis is enhanced by continuous traction in rabbit mandibular distraction osteogenesis. Journal of Cranio-Maxillofacial Surgery, 2009. 37(7): p. 405-411.

[25] 25. Park, J.-T., et al., A piezoelectric motor-based microactuator-generated distractor for continuous jaw bone distraction. Journal of Craniofacial Surgery, 2011. 22(4): p. 1486-1488.

[26] 26. Schmelzeisen, R., G. Neumann, and R. Von der Fecht, Distraction osteogenesis in the mandible with a motor-driven plate: a preliminary animal study. British Journal of Oral and Maxillofacial Surgery, 1996. 34(5): p. 375-378.

[27] 27. Ploder, O., et al., Mandibular lengthening with an implanted motor-driven device: preliminary study in sheep. British Journal of Oral and Maxillofacial Surgery, 1999. 37(4): p. 273-276.

[28] 28. Troulis, M.J., et al., Effects of latency and rate on bone formation in a porcine mandibular distraction model. Journal of oral and maxillofacial surgery, 2000. 58(5): p. 507-513.

[29] 29. Yeshwant, K., et al., Analysis of skeletal movements in mandibular distraction osteogenesis. Journal of oral and maxillofacial surgery, 2005. 63(3): p. 335-340.

[30] 30. Ritter, L., et al., Range of curvilinear distraction devices required for treatment of mandibular deformities. Journal of oral and maxillofacial surgery, 2006. 64(2): p. 259-264.

[31] 31. Alveolar distraction technique at the mandible. 2015; Available from: https://pocketdentistry.com/42-bone-augmentation-alveolar-distraction-osteogenesis/.

[32] 32. Avinash Kumar, N.B., MOTORIZED DISTRACTION OSTEOGENESIS, in Annual Product Confrence. 2016: India.

[33] 33. Chung, M., et al., An Implantable Battery System for a Continuous Automatic Distraction Device for Mandibular Distraction Osteogenesis. Journal of Medical Devices, 2010. 4(4): p. 045005.

[34] 34. Crane, N.B., et al. Design and Feasibility Testing of a Novel Device for Automatic Distraction Osteogenesis of the Mandible. in ASME 2004 International Design Engineering Technical Conferences and Computers and Information in Engineering Conference. 2004. American Society of Mechanical Engineers.

[35] 35. Aykan, A., et al., Mandibular distraction osteogenesis with newly designed electromechanical distractor. Journal of Craniofacial Surgery, 2014. 25(4): p. 1519-1523.

[36] 36. Savoldi, F., et al., The biomechanical properties of human craniofacial sutures and relevant variables in sutural distraction osteogenesis: a critical review. Tissue Engineering Part B: Reviews, 2018. 24(1): p. 25-36.

[37] 37. Dundar, S., et al., Comparison of the Effects of Local and Systemic Zoledronic Acid Application on Mandibular Distraction Osteogenesis. Journal of Craniofacial Surgery, 2017. 28(7): p. e621-e625.

[38] 38. Meyers, N., et al., Novel systems for the application of isolated tensile, compressive, and shearing stimulation of distraction callus tissue. PloS one, 2017. 12(12): p. e0189432.

[39] 39. Keßler, P., J. Wiltfang, and F.W. Neukam, A new distraction device to compare continuous and discontinuous bone distraction in mini-pigs: a preliminary report. Journal of Cranio-Maxillofacial Surgery, 2000. 28(1): p. 5-11.

[40] 40. Magill, J.C., et al., Automating skeletal expansion: An implant for distraction osteogenesis of the mandible. Journal of medical devices, 2009. 3(1): p. 014502.

[41] 41. Ayoub, A. and W. Richardson, A new device for microincremental automatic distraction osteogenesis. British Journal of Oral and Maxillofacial Surgery, 2001. 39(5): p. 353-355.

[42] 42. Mofid, M.M., et al., Spring-mediated mandibular distraction osteogenesis. Journal of Craniofacial Surgery, 2003. 14(5): p. 756-762.

[43] 43. Zhou, H.-Z., et al., Transport distraction osteogenesis using nitinol spring: an exploration in canine mandible. Journal of Craniofacial Surgery, 2006. 17(5): p. 943-949.

[44] 44. Idelsohn, S., et al., Continuous mandibular distraction osteogenesis using superelastic shape memory alloy (SMA). Journal of Materials Science: Materials in Medicine, 2004. 15(4): p. 541-546.

[45] 45. Yamauchi, K., et al., Timed-release system for periosteal expansion osteogenesis using NiTi mesh and absorbable material in the rabbit calvaria. Journal of Cranio-Maxillo-Facial Surgery, 2016. 44(9): p. 1366-1372.

[46] 46. Wee, J., et al., Development of a Force-Driven Distractor for Distraction Osteogenesis. Journal of Medical Devices, 2011. 5(4): p. 041004.

[47] 47. Ayoub, A., W. Richardson, and J. Barbenel, Mandibular elongation by automatic distraction osteogenesis: the first application in humans. British Journal of Oral and Maxillofacial Surgery, 2005. 43(4): p. 324-328.

[48] 48. Van Strijen, P., et al., Complications in bilateral mandibular distraction osteogenesis using internal devices. Oral Surgery, Oral Medicine, Oral Pathology, Oral Radiology, and Endodontology, 2003. 96(4): p. 392-397.

[49] 49. Tong, H., et al., Midface distraction osteogenesis using a modified external device with elastic distraction for crouzon syndrome. Journal of Craniofacial Surgery, 2017. 28(6): p. 1573-1577.

[50] 50. Hatefi, S., O. Ghahraei, and B. Bahraminejad, Design and Development of a Novel Multi-Axis Automatic Controller for Improving Accuracy in CNC Applications. Majlesi Journal of Electrical Engineering, 2017. 11(1).

[51] 51. Hatefi, S., O. Ghahraei, and B. Bahraminejad, Design and Development of a Novel CNC Controller for Improving Machining Speed. Majlesi Journal of Electrical Engineering, 2016. 10(1): p. 7.