Investigating on process variables effect of AISI 304 stainless steel machining using minimum quantity lubricant on cutting force

Journal of Simulation and Analysis of Novel Technologies in Mechanical Engineering

دوره 14، شماره 4، اسفند 2022، صفحه 45-51   

نوع مقاله: Research article

نویسندگان

Mohammad Ali Safataj؛ Sayed Ehsan Mirmohammadsadeghi^* ؛ Reza Abedinzadeh

Department of Mechanical Engineering, Khomeinishahr Branch, Islamic Azad University, Khomeinishahr/Isfahan, Iran

چکیده

In the machining process, the friction between the tool and the surface being machined, in addition to the destructive effects on tool wear and surface quality, increases the cutting force. By applying lubricant, it is possible to reduce the friction force in the machining process, and as a result, the cutting force is reduced. Due to the harmful environmental effects of excessive use of lubricants, the method of minimum quantity lubricant (MQL) can be helpful. In this method, fluid is applied with controlled flow and pressure. In this research, the effect of machining conditions on the cutting force for the machining process of AISI 304 stainless steel, using the method of minimum quantity lubricant has been investigated. The results show that with the increase in the cutting speed, the cutting force has decreased. Also, with the increase of injection pressure when applying the lubricating fluid using the method of the minimum quantity lubricant, a significant increase in the cutting force has been observed.

کلیدواژه‌ها

Cutting force؛ Minimum quantity of lubricant (MQL)؛ AISI 304 stainless steel؛ Cutting speed؛ Injection pressure

مراجع

 

[1] Mirmohammadsadeghi, S. E., & Amirabadi, H. (2018). High-pressure jet-assisted turning of AISI 304: Experimental and multi-objective optimization approach. Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, 232(6), 734-750.

[2] Ji, X., Zhang, X., Li, B., & Liang, S. Y. (2014). Modeling the effects of minimum quantity lubrication on machining force, temperature, and residual stress. Machining Science and Technology, 18(4), 547-564.

[3] Çakır, A., Yağmur, S. E. L. Ç. U. K., Kavak, N., Küçüktürk, G. Ö. K. H. A. N., & Şeker, U. (2016). The effect of minimum quantity lubrication under different parameters in the turning of AA7075 and AA2024 aluminum alloys. The International Journal of Advanced Manufacturing Technology, 84(9), 2515-2521.

[4] Kumar, S., Singh, D., & Kalsi, N. S. (2017). Analysis of surface roughness during machining of hardened AISI 4340 steel using minimum quantity lubrication. Materials Today: Proceedings, 4(2), 3627-3635.

[5] Hadad, M., & Sadeghi, B. (2013). Minimum quantity lubrication-MQL turning of AISI 4140 steel alloy. Journal of Cleaner Production, 54, 332-343.

[6] Ali, S. M., Dhar, N. R., & Dey, S. K. (2011). Effect of minimum quantity lubrication (mql) on cutting performance in turning medium carbon steel by uncoated carbide insert at different speed-feed combinations. Advances in Production Engineering & Management, 6(3).

[7] KarimiPour, A., Toghraie, D., Akbari, O. A., Zarringhalam, M., & Ahmadi Sheikh Shabani, G. (2016). Experimental investigation of the effect of suspended nanoparticles into conventional fluid on the heat transfer improvement. Journal of Simulation and Analysis of Novel Technologies in Mechanical Engineering, 9(2), 209-220.

[8] Chaudhari, S. S., Khedkar, S. S., & Borkar, N. B. (2011). Optimization of process parameters using Taguchi approach with minimum quantity lubrication for turning. International Journal of Engineering Research and Applications (IJERA), 1(4), 1268-1273.

[9] Sadr, P., Kolahdooz, A., & Eftekhari, S. A. (2015). The effect of electrical discharge machining parameters on alloy DIN 1.2080 using the Taguchi method and optimal determinant. Journal of Simulation and Analysis of Novel Technologies in Mechanical Engineering, 8(2), 71-89.

[10] Ekinovic, S., Prcanovic, H., & Begovic, E. (2015). Investigation of influence of MQL machining parameters on cutting forces during MQL turning of carbon steel St52-3. Procedia engineering, 132, 608-614.

[11] Najiha, M. S., Rahman, M. M., Yusoff, A. R., & Kadirgama, K. (2012). Investigation of flow behavior in minimum quantity lubrication nozzle for end milling processes. International Journal of Automotive and Mechanical Engineering, 6(1), 768-776.

[12] Khan, M. M. A., Mithu, M. A. H., & Dhar, N. R. (2009). Effects of minimum quantity lubrication on turning AISI 9310 alloy steel using vegetable oil-based cutting fluid. Journal of materials processing Technology, 209(15-16), 5573-5583.

[13] Kouam, J., Songmene, V., Balazinski, M., & Hendrick, P. (2015). Effects of minimum quantity lubricating (MQL) conditions on machining of 7075-T6 aluminum alloy. The International Journal of Advanced Manufacturing Technology, 79(5), 1325-1334.