Feed Stock Fabrication of AISI 4605 Steel for Fused Deposition Modeling and Sintering and Designing of Its Extruder Mechanism

ADMT Journal

دوره 15، شماره 4، اسفند 2022، صفحه 125-132   

نوع مقاله: Original Article

شناسه دیجیتال (DOI): 10.30486/admt.2023.1961907.1358

نویسندگان

Amir H Rahimi^* ؛ Jamal Zamani

Department of Mechanical Engineering, K.N. Toosi University of Technology, Iran

چکیده

Fused Deposition Modeling and Sintering (FDMS) is one of the indirect and emerging processes of Additive Manufacturing (AM) for the production of metal parts, which is a combination of AM process and Metal Injection Molding (MIM). This study laboratory made a raw material (Feed Stock) composing of high percentage of metal powder (particle in nano-scale) and polymeric materials; and then, designed an extruder to simulate melting and extruding process by Computational Fluid Dynamic (CFD). The different variables such as the nozzle diameter (D) of 1, 2, 3 and 4 mm and compression zone length (L2) of 100, 200 and 300 mm were simulated to investigate their impacts on flow rate and required torque to rotate screw. The findings showed that components of feed stock for high physical and mechanical properties of FDMS should account for 55 wt.% of paraffin wax, 25 wt.% of polypropylene, 15 wt.% of carnauba wax and 5 wt.% of stearic acid with optimum percentage of metal powder of 90 wt.%. Also, the optimum value of extruder diameter and compression zone length were 2mm and 200 mm, respectively. 

کلیدواژه‌ها

Additive Manufacturing؛ AISI 460 Steel Alloy؛ Extruder Screw؛ Fused Deposition Modeling and Sintering

مراجع

• ASTM Standard, F2792, Standard Terminology for Additive Manufacturing Technologies, ASTM International, West Conshohocken, Pennsylvania, 2012.
• West, A. P., Sambu, S. P., and Rosen, D. W., A Process Planning Method for Improving Build Performance in Stereolithography, Computer Aided Design, 2001, pp. 65–79.
• Li, N., Huang, S., Zhang, G., Qin, R., Liu, W., Xiong, H., Shi, G., and Blackburn, J., Progress in Additive Manufacturing on New Materials: A Review, J. Mater. Sci. Technol., Vol. 35, No. 2, 2019, pp. 242–269.
• Rahimi, A. H., Zamani, J., Development of a Feedstock for Additive Manufacturing of 4605 Steel Compact by FDMS Process, Transactions of the Indian Institute of Metals, 2022, pp. 1-7.
• Agarwala, M., Bourell, D., and Beaman, J., Direct Selective Laser Sintering of Metals, Rapid Prototyping, No. 1, 1995, pp. 26–36.
• Aghanajafi, C., Daneshmand, S., and Nadooshan, A. A., Influence of Layer Thickness on The Design of Rapid-Prototyped Models, Journal of aircraft, Vol. 46, No. 3, 2009, 981-987.
• Korinko, P. S., Adams, T. M., Malene, S. H., Gill, D., and Smugeresky, J., Laser Engineered Net Shaping for Repair and Hydrogen Compatibility, Weld. J., Vol. 90, No. 9, 2011.
• Daneshmand, S., Ahmadi, A., and Aghanajafi, C., Design and Production of Wind Tunnel Testing Models with FDM Technology Using ABSi, International Journal of Manufacturing Research, Vol. 4, No. 2, 2009, pp. 120-136.
• Do, T., Seop Shin, Ch., Stetsko, D., VanConant, G., Vartanian, A., Pei, Sh., and Kwon, P., Improving Structural Integrity with Boron-Based Additives for 3D Printed 420 Stainless Steel, Procedia Manuf., Vol. 1, 2015, pp. 263–272.
• Rane, K., Strano, M., A Comprehensive Review of Extrusion-Based Additive Manufacturing Processes for Rapid Production of Metallic and Ceramic Parts, Adv. Manuf, Vol. 7, No. 2, 2019, pp. 155–173.
• Agarwala, M. K., Jamalabad, V. R., Langrana, N. A., Safari, A., Whalen Ph. J., and Danforth, S. C., Structural Quality of Parts Processed by Fused Deposition, Rapid Prototyp. J., Vol. 2, No. 4, 1996, pp. 4–19.
• Momeni, V., Hossein Alaei, M., Askari, A., Hossein Rahimi, A., and Nekouee, K., 2019. Effect of Carnauba Wax as A Part of Feedstock on The Mechanical Behavior of a Part Made Of 4605 Low Alloy Steel Powder Using Metal Injection Molding, Material Wissen chaft und Werk Stoff Technik, Vol. 50, No. 4, 2019, pp. 432-441.
• Bin L., Yuxiang, W., Ziwei, L., and Tao, Zh., Creating Metal Parts by Fused Deposition Modeling and Sintering, Mater. Lett. 18, Vol. 263, 2020.
• Rahimnia, A., Hesarikia, H., Rahimi, A., Karami, S. and Kaviani, K., Evaluation and Comparison of Synthesised Hydroxyapatite in Bone Regeneration: as an in Vivo Study, Journal of Taibah University Medical Sciences, Vol. 16, No. 6, 2021, pp. 878-886.
• Tarafdar, A., Razmkhah, O., Ahmadi, H., Liaghat, G., Chitsaz Charandabi, S., and Rezaei Faraz, M., Effect of Layering Layout on The Energy Absorbance of Bamboo-Inspired Tubular Composites, Journal of Reinforced Plastics and Composites, 2022, pp. 07316844211063865.
• Agarwala, M. K., Van Weeren, R., Vaidyanathan, R., Carrasquillo, G., Jamalabad, V., Langrana, N., Safari, A., Garofalini, S. H., and Danforth, S. C., Structural Ceramics by Fused Deposition of Ceramics, Vol. 6, 1995. pp. 1–8.
• Agarwala, M. K., Van Weeren, R., Bandyopadhyay, A., Whalen, P. J., Safari and A., Danforth, S. C., Fused Deposition of Ceramics and Metals: An Overview, Proc. Solid Free. Fabr. Symp., 1996, pp. 385–392.
• Yang, X., Xie, H., He, Q., Zhou, Z., Xu, X., Zhang, L., and Xie, Z., Study of Thermal Degradation of Binders for Ceramic Injection Melding by TGA-FTIR, Ceram. Int, Vol. 45, No. 8, 2019, pp. 10707–10717.
• Momeni, V., Askari, A., Alaei, M.H., Rahimi, A.H., Nekouee, K., and Zangi, H., The Effect of Powder Loading and Binder System on The Mechanical, Rheological and Microstructural Properties Of 4605 Powder in MIM Process, Transactions of the Indian Institute of Metals, Vol. 72, No. 5, 2019, pp. 1245-1254.
• He, Q., Jiang, J., Yang, X., Zhang, L., Zhou, Zh., Zhong, Y., and Shen, Zh., Additive Manufacturing of Dense Zirconia Ceramics by Fused Deposition Modelling Via Screw Extrusion, Journal of the European Ceramic Society, Vol. 41, 2021, pp. 1033–1040.
• Boparai, K. S., Singh, R., and Singh, H., Development of Rapid Tooling Using Fused Deposition Modelling: A Review, Rapid Prototyping Journal, Vol. 22, No. 2, 2016, pp. 281–299.
• Huang, B., Liang, S., and Qu, X., The Rheology of Metal Injection Melding, J. Mater. Process. Technol., Vol. 137, No. 1, 2003, pp. 132–137.
• Gülsoy, H. Ö., German, R. M., Production of Micro-Porous Austenitic Stainless Steel by Powder Injection Molding, Scr. Mater., Vol. 58, No. 4, 2008, pp. 295–298.
• Supriadi, S., Baek, E. R., Choi, C. J., and Lee, B. T., Binder System for STS 316 Nano-Powder Feedstocks in Micro-Metal Injection Molding, J. Mater. Process. Technol., Vol. 187–188, 2007, pp. 270–273.
• Onbattuvelli, V. P., Enneti, R. K., Park, S. J., and Atre, S. V., The Effects of Nanoparticle Addition on SiC and AlN Powder-Polymer Mixtures: Packing and Flow Behavior, Int. J. Refract. Met. Hard Mater., Vol. 36, 2013, pp. 183–190.
• Bellini, A., Bertoldi, M., Liquefier Dynamics in Fused Deposition Modelling, Journal of Manufacturing Science and Engineering, Vol. 126, 2004, pp. 237-246.
• Sa’ude, N., Ibrahim, M., and Ibrahim, M. H. I., Melt Flow Behavior of Polymer Matrix Extrusion for Fused Deposition Modeling (FDM), Vol. 660, 2014, pp. 89–93, AMM.
• Cobos, C. M., Garzón, L., López Martinez, J., Fenollar, O., and Ferrandiz, S., Study of Thermal and Rheological Properties of PLA Loaded with Carbon and Halloysite Nanotubes for Additive Manufacturing, Rapid Prototyping Journal, Vol. 25 No. 4, 2019, pp. 738-743.
• Ramanath, H. S., Chua, C. K., and Leong, K. F., Melt Flow Behaviour of Poly-I Caprolactone in Fused Deposition Modelling, Journal of Material Science, Materials in Medicine, Vol. 19, No. 7, 2007, pp. 2541-2550.
• Nikzad, M., Masood, S. H., Sbarski, I., and Groth, A., Thermo-Mechanical Properties of a Metal-Filled Polymer Composite for Fused Deposition Modelling Applications, In: Proceedings of 5th Australasian Congress on Applied Mechanics, Brisbane, Australia: Australian Congress on Applied Mechanics, 2007.
• Sotomayor, M. E., Várez, A., and Levenfeld, B., Influence of Powder Particle Size Distribution on Rheological Properties of 316L Powder Injection Moulding Feedstocks, Powder Technol., Vol. 200, No. 1–2, 2010, pp. 30–36.
• Atre, S. V., Weaver, T. J., and German, R. M., Injection Molding of Metals and Ceramics, Metal Powder Industries Federation, 1998.
• Ho, Y. L., Lin, S. T., Debinding Variables Affecting the Residual Carbon Content of Injection-Molded Fe-2 Pct Ni steels, Metall. Mater. Trans. A, Vol. 26, No. 1, 1995, pp. 133–142.
• Matsuda, M., Miura, H., Mechanical Properties of Injection Molded Fe-6% Ni-0.4% C Steels with Varying Mo Contents of 0.5 to 2%, Met. Mater. Int., Vol. 9, No. 6, 2003, pp. 537–542.
• Ahn, S., Park, S. J., Lee, S., Atre, S. V., and German, R. M., Effect of Powders and Binders on Material Properties and Melding Parameters in Iron and Stainless-Steel Powder Injection Melding Process, Powder Technology, Vol. 193, 2009, pp. 162-169.
• Lin, K., Wear Behavior and Mechanical Performance of Metal Injection Molded Fe–2Ni Sintered Components, Mater. Des., Vol. 32, No. 3, 2011, pp. 1273–1282.
• Klainerman, S., Majda, A., CompressibL2e and IncompressibL2e fL2uids, Communications in Pure AppL2ied Mathematics, Vol. 35, 1982, pp.629-651.
• German, R. M., Bose, A., Injection Molding of Metals and Ceramics, Metal Powder Industries Federation, 1997.
• Sotomayor, M. E., Levenfeld, B., and Várez, A., Powder Injection Moulding of Premixed Ferritic and Austenitic Stainless-Steel Powders, Mater. Sci. Eng. A, Vol. 528, No. 9, 2011, pp. 3480–3488.