Numerical Analysis of Melting Process of Compounds Containing Nanoparticles for the Development of Phase Change Process

Journal of Simulation and Analysis of Novel Technologies in Mechanical Engineering

مقاله 2، دوره 7، شماره 2، بهمن 2014، صفحه 29-13   

نوع مقاله: Persian

نویسندگان

N. Pourmohammad¹؛ N. Mostafavinia^{* 2}؛ A. Hassanzadeh²

¹Associate Prof., Department of Mechanical Engineering, Urmia University, Urmia, Iran

²PhD Student, Department of Mechanical Engineering, Urmia University, Urmia, Iran

چکیده

In this work, the melting process of compounds containing nanoparticles of NePCM in a square hole with different angles affected by two pairs of well-spring heat source on horizontal walls was numerically investigated. Four different configurations of elements were employed to investigate the effect of changes in the position of elements on the horizontal walls of the well-spring landscape on the ratio of liquid fraction. In the first case, the springs and wells have been located on horizontal walls separately. The environmental condition in the second case is that the spring-well elements have been set on the horizontal walls alternatively. In the third case, springs are on the left of well elements, and ultimately in the fourth case, spring and well elements are all set at the bottom of horizontal walls. Results show that in the first arrangement, using 2%weight of Al₂O₃ nanoparticles, compared to other cases, the highest ratio of liquid fraction is obtained.

کلیدواژه‌ها

Melting rate؛ Paraffin؛ nanoparticles

مراجع

[1] FaridM.M., KhudhairA.M., RazackS.A.K., Al-HallajS., A review on phase change energy storage: materials and applications, Energy Conversion and Management, Vol. 45, No.9–10,2004, pp. 1597–1615.

[2] ZhouD., ZhaoC.Y., TianY., Review on thermal energy storage with phase change materials (PCMs) in building applications, Applied Energy, Vol. 92, 2012, pp.593–605.

[3] ZalbaB., Marı́nJ.M., CabezaL.F., MehlingH., Review on thermal energy storage with phase change: materials, heat transfer analysis and applications, Applied Thermal Engineering, Vol. 23, No. 3, 2003, pp.251–283.

[4] AtulS., TyagiV.V., ChenC.R., BuddhiD., Review on thermal energy storage with phase change materials and applications, Renewable and Sustainable Energy Reviews, Vol. 13 ,2009, pp. 318–345.

[5] MengE., Yu, ZhanG., HeY., Experimental and numerical study of the thermal performance of a new type of phase change material room, Energy Conversion and Management, 74 ,2013, pp.386–394.

[6] ZhangY., ChenZ., WangQ., WuQ., Melting in an enclosure with discrete heating at a constant rate, Experimental Thermal and Fluid Science, Vol. 6 ,1993, pp.196–201.

[7] FarajiM., El QarniaH., Numerical study of melting in an enclosure with discrete protruding heat sources, Applied Mathematics Modeling, Vol. 34,2010, pp.1258–1275.

[8]KousksouT., MahdaouiM.,  AhmedA., MsaadA.A., Melting over a wavy surface in a rectangular cavity heated from below, Energy, Vol. 64,2014, pp.212-219.

[9] KhodadadiJ.M., HosseinizadehS.F., Nanoparticle-enhanced phase change materials (NEPCM) with great potential for improved thermal energy storage, International Communication in Heat and Mass Transfer,Vol. 34,2007, pp.534–543.

[10] ZengJ.L., SunL.X., XuF., TanZ.C., ZhangZ.H., ZhangJ., ZhangT., Study of a PCM based energy storage system containing Ag nanoparticles, Journal of Thermal Analysis and Calorimetry, Vol. 87,2007, pp.369–373.

[11] WuS.Y., WangH., XiaoS., ZhuD.S., An investigation of melting/freezing characteristics of nanoparticle-enhanced phase change materials, Journal of Thermal Analysis and Calorimetry, Vol. 110,2012, pp.1127–1131.

[12] ChowL.C., ZhongJ.K., Thermal conductivity enhancement for phase change storage media, International Communications in Heat and Mass Transfer, Vol. 23,1996, pp. 91–100.

[13] VajjhaR.S., DasD.K., Measurement of thermal conductivity of threenanofluids and development of new correlations, Journal of Heat and Mass Transfer,Vol. 52,2009, pp.4675–4682.

[14] HoC.J., GaoT.Y., Preparation and thermophysical properties of nanoparticle-in-paraffin emulsion as phase change material, International Communications in Heat and Mass Transfer,Vol. 36, No.5, 2009, pp.467-470.

[15] KashaniS., RanjbarA.A., AbdollahzadehM., SebtiS., Solidification of nano-enhanced phase change material (NEPCM) in a wavy cavity, Heat Mass Transfer,Vol. 48,2012, pp. 1155–1166.

[16] HosseinizadehS.F., RabienatajDarziA.A., TanF.L., Numerical investigations of unconstrained melting of nano-enhanced phase change material (NEPCM) inside a spherical container, International Journal of Thermal Science,Vol. 41,2012, pp.77–83.

 

 

[17] ArasuA.V., MujumdarA.S., Numerical study on melting of paraffin wax with Al2O3 in a square enclosure, International Communications in Heat and Mass Transfer,Vol. 39,2012, pp.8–16.

[18] SebtiS., MastianiM., MirzaeiH., DadvandA., KashaniS., HosseiniS.A., Numerical study of the melting of nano-enhanced phase change material in a square cavity, Journal of Zhejiang University Science A, Vol. 14, No.5, 2013, pp.307-316.

[19] HoC.J., GaoJ.Y., An experimental study on melting heat transfer of paraffin dispersed with Al2O3 nanoparticles in a vertical enclosure, International Journal of Heat and Mass Transfer, Vol. 62, 2013, pp.2–8.

[20] ZengY., FanL.W., XiaoY.Q., YuZ.T., CenK.F., An experimental investigation of melting of nanoparticle-enhanced phase change materials (NePCMs) in a bottom-heated vertical cylindrical cavity, International Journal of Heat and Mass Transfer, Vol. 66,2013, pp.111–117.

[21] El-HasadiY.M.F., KhodadadiJ.M., Numerical simulation of the effect of the size of suspensions on the solidification process of nanoparticle-enhanced phase change materials, Journal of Heat Transfer, Vol. 135, No.5, 2013, 052901.

[22] N.S. Dhaidan, J.M. Khodadadi, T.A. Al-Hattab, S.M. Al-Mashat, Experimental and numerical investigation of melting of phase change material/nanoparticle suspensions in a square container subjected to a constant heat flux, InternationalJournal of Heat and Mass Transfer, Vol. 66,2013, pp.672–683.

[23] DhaidanN.S., KhodadadiJ.M., Al-HattabT.A., Al-MashatS.M., Experimental and numerical study of constrained melting of n-octadecane with CuO nanoparticle dispersions in a horizontal cylindrical capsule subjected to a constant heat flux, InternationalJournal of  Heat and Mass Transfer, Vol. 67,2013, pp.523–534

[24] DhaidanN.S., KhodadadiJ.M., Al-HattabT.A., Al-MashatS.M., Experimental and numerical investigation of melting of NePCM inside an annular container under a constant heat flux including the effect of eccentricity, International Journal of Heat and Mass Transfer, Vol. 67 , 2013, pp.455–468.

[25] JourabianM., FarhadiM., SedighiK., On the expedited melting of phase change material (PCM) through dispersion of nanoparticles in the thermal storage unit, Computers and Mathematics with Applications,Vol. 67,2014,  pp.1358-1372.

[26] http://www.fluent.com.

[27] KandasamyR., WangX.Q., MujumdarA.S., Transient cooling of electronics using phase change material (PCM)-based heat sinks, Applied Thermal Engineering,Vol. 28,2008, pp.1047–1057.

[28] SasmitoA.P., KurniaJ.C., MujumdarA.S., Numerical evaluation of laminar heat transfer enhancement in nanofluid flow in coiled square tubes, Nanoscale Research Letters, Vol. 6, No.1, 2011, pp.1-14.

[29] ArasuA.V., SasmitoA.P., MujumdarA.S., Numerical performance study of paraffin wax dispersed with Alumina in a concentric pipe latent heat storage system, Thermal Science, Vol. 17, 2013, pp.419-430.

[30] VajjhaR.S., DasD.K., NamburuP.K., Numerical study of fluid dynamic and heat transfer performance of Al2O3 and CuOnanofluids in the flat tubes of a radiator, International Journal of Heat Fluid Flow, Vol. 31, 2010,  pp.613–621.