Mechanical Stresses in a Linear Plastic FGM Hollow Cylinder Due to Non-Axisymmetric Loads

Journal of Solid Mechanics

مقاله 2، دوره 8، شماره 4، اسفند 2016، صفحه 705-718   

نوع مقاله: Research Paper

نویسندگان

M Shokouhfar^* ؛ M Jabbari

South Tehran Branch, Islamic Azad University,Tehran, Iran

چکیده

In this paper, an analytical solution for computing the linear plastic stresses and critical pressure in a FGM hollow cylinder under the internal pressure due to non-Axisymmetric Loads is developed. It has been assumed that the modulus of elasticity was varying through thickness of the FGM material according to a power law relationship. The Poisson's ratio was considered constant throughout the thickness. The general form of mechanical boundary conditions is considered on the inside surfaces. In the analysis presented here the effect of non-homogeneity in FGM cylinder was implemented by choosing a dimensionless parameter, named m, which could be assigned an arbitrary value affecting the stresses in the cylinder. Distribution of stresses in radial, circumferential and shear directions for FGM cylinders under the influence of internal pressure were obtained. Graphs of variations of stress versus radius of the cylinder were plotted. The direct method is used to solve the Navier equations.  

کلیدواژه‌ها

Hollow cylinder؛ Non-Homogenous؛ Non- Axisymmetri؛ FGM؛ Elastic-plastic analysis

مراجع

[1] Lutz M.P., Zimmerman R.W., 1996, Thermal stresses and effective thermal expansion coefficient of functionally graded sphere, Journal of Thermal Stresses 19:39-54.
[2] Zimmerman R.W., Lutz M. P., 1999, Thermal stresses and thermal expansion in a uniformly heated functionally graded cylinder, Journal of Thermal Stresses 22:177-188.
[3] Jabbari M., Sohrabpour S., Eslami M.R., 2003, General solution for mechanical and thermal stresses in functionally graded hollow cylinder due to non-axisymmetric steady-state loads, Journal of Applied Mechanics 70:111-118.
[4] Poultangari R., Jabbari M., Eslami M.R. 2008, Functionally graded hollow spheres under non-axisymmetric thermo-mechanical loads, International Journal of Pressure Vessels and Piping 85: 295-305.
[5] Lu Y., Zhang K., Xiao J., Wen D., 1999, Thermal stresses analysis of ceramic/metal functionally gradient material cylinder, Applied Mathematics and Mechanics 20(4): 413-417.
[6] Shariyat M., Lavasani S.M.H., Khaghani M., 2010, Nonlinear transient thermal stress and elastic wave propagation analyses of thick temperature-dependent FGM cylinders, using a second-order point-collocation method, Applied Mathematical Modelling 34:898-918.
[7] Shariyat M., 2009, A nonlinear Hermitian transfinite element method for transient behavior analysis of hollow functionally graded cylinders with temperature-dependent materials under thermo-mechanical loads, International Journal of Pressure Vessels and Piping 86: 280-289.
[8] Lü C.F., Chen W.Q., Lim C.W., 2009, Elastic mechanical behavior of nano-scaled FGM films incorporating surface energies, Composites Science and Technology 69: 1124-1130.
[9] Afsar A.M., Sekine H., 2002, Inverse problems of material distributions for prescribed apparent fracture toughness in FGM coatings around a circular hole in infinite elastic media, Composites Science and Technology 62:1063-1077.
[10] Tajeddini V., Ohadi A., Sadighi M., 2011, Three-dimensional free vibration of variable thickness thick circular and annular isotropic and functionally graded plates on Pasternak foundation, International Journal of Mechanical Sciences 53:300-308.
[11] Nosier A., Fallah F., 2009, Nonlinear analysis of functionally graded circular plates under asymmetric transverse loading, International Journal of Non-Linear Mechanics 44:928-942.
[12] Zhang D.G., Zhou Y. H., 2008, A theoretical analysis of FGM thin plates based on physical neutral surface ,Computational Materials Science 44 :716-720.
[13] Fazelzadeh S.A., Hosseini M., 2007, Aero thermo elastic behavior of supersonic rotating thin-walled beams made of functionally graded materials, Journal of Fluids and Structures 23:1251-1264.
[14] Ootao Y., Tanigawa Y., 2004, Transient thermo elastic problem of functionally graded thick strip due to Non- uniform heat supply , Composite Structures 63(2):139-146.
[15] Jabbari M., Sohrabpour S., Eslami M.R., 2002, Mechanical and thermal stresses in a functionally graded hollow cylinder due to radially symmetric loads , International Journal of Pressure Vessels and Piping 79:493-497.
[16] Farid M. , Zahedinejad P. , Malekzadeh P., 2010, Three-dimensional temperature dependent free vibration analysis of functionally graded material curved panels resting on two-parameter elastic foundation using a hybrid semi-analytic, differential quadrature method, Materials and Design 31:2-13.
[17] Bagri A., Eslami M.R., 2008, Generalized coupled thermo elasticity of functionally graded annular disk considering the Lord–Shulman theory, Composite Structures 83:168-179.
[18] Jabbari M., Bahtui A., Eslami M.R., 2009, Axisymmetric mechanical and thermal stresses in thick short length functionally graded material cylinder, International Journal of Pressure Vessels and Piping 86: 296-306.
[19] Zamani Nejad M., Rahimi G.H., 2009, Deformations and stresses in rotating FGM pressurized thick hollow cylinder under thermal load, Scientific Research and Essay 4(3): 131-140.
[20] Batra R.C., Iaccarino G.L., 2008, Exact solutions for radial deformations of a functionally graded isotropic and incompressible second-order elastic cylinder, International Journal of Non-Linear Mechanics 43:383-398.
[21] Shao Z.S., Wang T.J., 2006, Three-dimensional solutions for the stress fields in functionally graded cylindrical panel with finite length and subjected to thermal/mechanical loads, International Journal of Solids and Structures 43: 3856-3874.
[22] Shabanaa Y.M., Noda N., 2001, Thermo-elasto-plastic stresses in functionally graded materials subjected to thermal loading taking residual stresses of the fabrication process into consideration, Composites: Part B 32: 111-121.
[23] Eraslan A.N., Akis T., 2006, Plane strain analytical solutions for a functionally graded elastic–plastic pressurized tube, International Journal of Pressure Vessels and Piping 83: 635-644.
[24] Eraslan A.N., Arselan E., 2007, Plane strain analytical solutions to rotating partially plastic graded hollow shafts, Turkish Journal of Engineering and Environmental Sciences 31: 273-288.
[25] Eraslan A.N., Akis T., 2005, Elastoplastic response of a long functionally graded tube subjected to internal pressure, Turkish Journal of Engineering and Environmental Sciences 29(6): 361-368.
[26] Alla M.N., Ahmed K. I. E., Allah I. H., 2009, Elastic–plastic analysis of two-dimensional functionally graded materials under thermal loading, International Journal of Solids and Structures 46: 2774-2786.
[27] Lu H. Ç., 2011, Stress analysis in a functionally graded disc under mechanical loads and a steady state temperature distribution, Indian Academy of Sciences Sadhana 36: 53-64.
[28] Jahromi B. H., 2012, Elasto-plastic stresses in a functionally graded rotating disk, Journal of Engineering Materials and Technology 134: 021004-021015.
[29] Sadeghian M., Toussi H. E., 2012, Elasto-plastic axisymmetric thermal stress analysis of functionally graded cylindrical vessel, Journal of Basic and Applied Scientific Research 2(10): 10246-10257.
[30] Mendelson A., 1986, Plasticity: Theory and Application, New York, MacMillan.