A new plan to connect aluminum tubes of subsurface structures

Journal of Simulation and Analysis of Novel Technologies in Mechanical Engineering

مقاله 6، دوره 9، شماره 3 - شماره پیاپی 27، بهمن 2016، صفحه 455-466   

نوع مقاله: Persian

نویسندگان

Gholamreza Mazruei¹؛ ali Heidari^{* 2}

¹Graduate Student, Faculty of Mechanical Engineering, Islamic Azad University of Khomeini Shahr

²Assistant Professor, Young Researchers and Elite Club, Khomeinishahr Branch, Islamic Azad University, Khomeinishahr, Iran

چکیده

 
In this study, a new method for joining aluminum tubes in subsurface structures using steel converting and aluminum welding are presented and reviewed. But near the weld area is under high thermal cycle and will cause residual stresses in heat affected zone. Therefore for assessment of proposed connection from the perspective of residual stress by using the finite element method welding of tubes has been modeled in three dimensions. Thermal history is determined from thermal analysis and then the residual stresses due to welding are calculated. Because of the sensitivity of subject, the simulation process and properties are validated. The mechanical and thermal properties have been considered as a function of temperature. According to current, voltage and speed electrode, heat flux is applied by Goldak's heat source model. The modeling results were good agreement with experimental results and show that the initiative plan can be used to connect aluminum tubes of subsurface structures.

کلیدواژه‌ها

welding؛ aluminum tubes؛ Residual stress؛ Finite Element Method

مراجع

[1] Murugan S. , Rai S.K. , Kumar P.V., International Jornal of Pressure Vessels Piping, 78,2001,307-317.

[2] Brickstad B. , Josefson B.L. , International Jornal of Pressure Vessels and Piping, 75, 1998, 11-25.

[3] Goldack J. , Chakravarti A. , Bibby M. , Metallurgical Transaction B 15, 1984,299-305.

[4] Wen S.W. , Hilton P. , Farrugia D.C.J. , Strain jornal of the Britsh Socicty for Strain Measurement 37,2001,5-18

[5] Tsai C.L., Dong Y. , Dong P. ,77 Annual AWS , Chieago, USA, 21-25 April 1996, p. 51.

[6] Li M. , Atteridge D.G. , Meekisho LL. , Trends in Welding Research, 4 International Conference, Gaylingurg, Tennesse, USA, 5-8 JUNE 1995,PP. 51-56

[7] Deng D. , Muakawa H. , Computational Materials Science 37, 2006, 269-227.

[8] آشنایی و طرز کار با نرم افزار ABAQUS ، تالیف- محمود فرزین، سید حسین دیباجیان، اصفهان، جهاد دانشگاهی، واحد صنعتی اصفهان، 1390

[9] J. Cairns, R. Pidn, F. Paris, A. Blazquez and J. C. Marin ."A SIMPLIFIED NUMERICAL ANALYSIS OF RESIDUAL STRESSES IN ALUMINUM WELDED PLATES"(1994)

[10] Dragi Stamenković, MSc. Ivana Vasović, BSc. "Finite Element Analysis of Residual Stress in Butt Welding Two Similar Plates"(2012)

[11] John A. Goldak, Mehdi Akhlaghi, "Coputational Welding Mechnics".(2005)

 [12] Yaowu Shia, Zhunxiang Hanb,"Effect of weld thermal cycle onmicro structure and fracture toughness of simulated heat-affected zone for a 800MPa grade high strength low alloy steel", Journal of materials processing technology 207(2008)30-39

[13] جوشکاری آلومینیوم و آلیاژهای آن، تالیف- ج. مترز، ترجمه- ج. مزروعی، ع. ورمزیار،اراک، نشر نویسنده، 1390