The Impact of Die Corner Radius and Friction Coefficient on Bulge Forming of T-Shaped Copper Tubes using Finite-Element Method and Experimental Analysis

ADMT Journal

مقاله 4، دوره 10، شماره 1، خرداد 2017، صفحه 31-38   

نوع مقاله: Original Article

نویسندگان

M. Ahmadpour¹؛ Omid Ghahraei^{* 2}

¹Department of Mechanical Engineering, Khomeinishahr Branch, Islamic Azad University, Isfahan, Iran

²Center for Advanced Engineering Research, Majlesi Branch, Islamic Azad University, Isfahan, Iran. *Corresponding author

چکیده

In this paper, the effects of various parameters on the process of T-shaped copper tube bulge forming have been investigated. This evaluation is based on the properties of the copper tubes, properties of polyurethane rod and practical conditions of a bulge forming process such as the friction coefficient between die and tube, between tube and rod, boundary conditions and their constraints. The effect of each condition on a T-shaped copper tube has been explicitly simulated using the Abaqus software. The experimental results have been validated by conducting a series of experiments. After simulating the process, the effect of other parameters such as die corner radius, friction coefficient, thickness of the tube and counterpoise can be evaluated and used in practical experiments. Then, the simulation results have been compared with the obtained results from the experiments. Once the accuracy of the simulation results has been endorsed, the optimal values of different parameters have been determined using simulations. The optimal values for die corner radius, friction coefficient and counterpoise are 5 mm, 0.05 and 200 N, respectively. The findings shows the positive effect of utilization of optimal value for die corner radius, optimal value for counterpoise and lubricate on optimize forming process properties.

کلیدواژه‌ها

Bulge forming؛ Copper tube؛ Die corner radius؛ Friction Coefficient؛ polyurethane

مراجع

[1]     Zheng, Ch., Sun, Sh., Wang, and Zh. W., “Effect of laser energy on the deformation behavior in micro scale laser bulge forming”, Applied Surface Science, Vol. 257, 2010, pp. 1589-1595.

[2]     Taleff, E. M., Hector, Jr. L. G., and Verma, R., “Material Models for Simulation of Super plastic Mg Alloy Sheet Forming”, Materials Engineering and Performance, Vol. 19, 2010, pp. 488-494.

[3]     Hassan, M. A., Saleh, M. A. E., and Takakura, N., “Effect of bulge shape on wrinkling formation and strength of stainless steel thin sheet”, Materials and Design, Vol. 42, 2012, pp. 37-45.

[4]     Dohmannand, F., Hartl, C., “Liquid-Bulge-Forming as a Flexible Production Method”, Materials Processing Technology, Vol. 45, 1994, pp. 377, 382.

[5]     Hashemi, S. J., Moslemi-Naeini, H., and Liaghat, G. H., “Prediction of forming limit curve using ductile fracture criteria in hydro-forming of aluminum tubes”, Applied and Computational Sciences in Mechanics, Vol. 25, 2014, pp. 11-17.

[6]     Song, S. W., Kim, W. J., Kim, J., and Kang, B. S., ”Analytical and numerical analysis of bursting failure prediction in tube hydro forming”, Materials Processing Technology, Vol. 164, 2005, pp. 1618-1623.

[7]     Ahmetoglu, M., Altan, T., “Tube hydro forming: state-of-the-art and future trends”, Materials Processing Technology, Vol. 98, 2000, pp. 25-33.

[8]     Koc, M., Billur, E., Cora, ÖN., “An experimental study on the comparative assessment of hydraulic bulge test analysis methods”, Materials & Design, Vol. 32, 2011, pp. 272-281.

[9]     Sokolowski, T., Gerke, K., Ahmetoglu, M., and Altan, T., “Evaluation of tube formability and material characteristics: hydraulic bulge testing of tubes”, Materials Processing Technology, Vol. 98, 2000, pp. 34-40.

[10]  Ashrafi, A., Khalili, K., “Studying the stress-strain curve of C12200 Copper tube using hydraulic bulge test in T-shaped die”, Modares Mechanical Engineering, Vol. 14, 2015, pp. 95-106.

[11]  Hartl, C., “Research and advances in fundamentals and industrial application of hydro forming”, Material Processing Technology, Vol. 167, 2005, pp. 383-392.

[12]  Song, W. J., Heo, S. C., and Ku, T. W., “Evaluation of effect of flow stress characteristics of tubular material on forming limit in tube hydro forming process”, Machine Tools and Manufacture, Vol. 50, 2010, pp. 753-764.

[13]  Moslemi-Naeini, H., Hashemi, S. J., and Liaghat, G. H., “Analytical prediction of limit strains and limit stresses in hydro forming of anisotropic aluminum tubes”, Modares Mechanical Engineering, Vol. 14, 2014, pp. 133-140.

[14]  Hashemi, R., Assempour, A., and Abad, E. M. K., “Implementation of the forming limit stress diagram to obtain suitable load path in tube hydro forming considering M–K model”, Materials & Design, Vol. 30, 2009, pp. 3545-3553.

[15]  Hashemi, R., Abrinia, K., and Assempour, A., “The strain gradient approach to predict necking in tube hydro forming”, Manufacturing Processes, Vol. 15, 2013, pp. 51-55.

[16]  Gheisari, M., Javanroody, F., “Investigation of the double bulge tube hydro forming process and spiral forming”, Teacher–Mechanics Engineering Magazine 10, Iran, 2010.

[17]  Jabari, I., “Modeling and Simulation of polymer reactions”, Amirkabir University of Technology Press, Iran, 2001.

[18]  Mac Donald, B., Hashmi, M. S. J., “Finite Element Simulation of Bulge Forming OF a Cross-Joint From a Tubular Blank”, Materials Processing Technology, Vol. 103, 2000, pp. 333-342.

[19]  Tarkesh, E. R., Qarany, A., Shahnazari, H., and Nejatbakhsh, H., “A Comprehensive Guide for Modeling and Analysis in ABAQUS”, Abed Press, Iran, 2011.

[20]  Bilmir, F., “Synthetic Polymers: producing large molecules”, Amirkabir University of Technology Press, Iran, 2000.