Synthesis of B4C - Nano TiB2 Composite Nano Powder by the Chemical Precipitation Method

ADMT Journal

مقاله 7، دوره 10، شماره 4، اسفند 2017، صفحه 55-61   

نوع مقاله: Original Article

نویسندگان

M. Saeedi Heydari^* ؛ H. R. Baharvandi

Faculty of Materials and Manufacturing Processes, Malek-Ashtar University of Technology, Tehran, Iran

چکیده

The aim of this research is to determine the proper concentration of Titanium Tetra IsoPropoxide (TTIP) and select the right temperature and time of calcinations for the synthesis of B₄C-nano TiB₂ composite Nano powder by the chemical precipitation method. For this purpose, first, solutions with TTIP molar concentrations of 0.1, 0.05 and 0.03 were prepared and the optimal molar concentration of TTIP was determined to be 0.05. Then, a diluted solution of distilled water and TTIP was mixed with Isopropanol Alcohol containing B₄C micropowder. In this mixture, Titanium Hydroxide nanoparticles were initially synthesized and then, to convert the Ti(OH)₄ to TiB₂, the above mixture were calcined in a furnace, under Argon atmosphere. The calcination process was carried out at temperatures of 750, 1000 and 1250 ºC. It was observed that the most suitable temperature for the formation of the TiB₂ phase is 1250 ºC and that the lower temperatures only lead to the formation of the TiO₂ phase. It was also observed that, at the calcination temperature of 1250 ºC, the most appropriate time duration for the conversion of Ti(OH)₄ nanoparticles to TiB₂ nanoparticles is 30 minutes, during which B₄C-nano TiB₂ composite Nano powders form, with most of the TiB₂ particle sizes being in the range of 30-60 nm.

کلیدواژه‌ها

B4C-nano TiB2؛ Chemical precipitation؛ Nano powder؛ TTIP

مراجع

[1]    Roy, T., Subramanian, C., and Suri, A., “Pressureless Sintering of Boron Carbide”, Ceramics International, Vol. 32, No. 3, 2006, pp. 227-33.

[2]    Najafi, A., Golestani-Fard, F., Rezaie, H., and Ehsani, N., “Effect of APC Addition on Precursors Properties During Synthesis of B₄C Nano Powder by a Sol–Gel Process”, Journal of Alloys and Compounds, Vol. 509, No. 3, 2011, pp. 9164-70.

[3]    Lee, H., Speyer, RF., “Pressureless Sintering of Boron Carbide”, Journal of the American Ceramic Society, Vol. 86, No. 9, 2003, pp. 1468-1473.

[4]    Srivatsan, T., Guruprasad, G., Black, D., Radhakrishnan, R., and Sudarshan, T., “Influence of TiB₂ Cntent on Microstructure and Hardness of TiB₂–B₄C Composite”, Powder Technology, Vol. 159, No. 3, 2005, pp. 161-167.

[5]    McCuiston, R., LaSalvia, J., and Moser, B., “Effect of Carbon Additions and B₄C Particle Size on the Microstructure and Properties of B₄C‐TiB₂ Composites”, Mechanical Properties and Performance of Engineering Ceramics and Composites III, 2007, 257.

[6]    Itoh, H., Sugiura, K., and Iwahara, H., “Preparation of TiB₂-B₄C Composites by High Pressure Sintering”, Journal of alloys and compounds, Vol. 232, No. 1, 1996, pp. 186-191.

[7]    Pérez Delgado, Y., Staia, M., Malek, O., Vleugels, J., and De Baets, P., “Friction and Wear Response of Pulsed Electric Current Sintered TiB₂-B₄C Ceramic Compositeˮ, Wear, 2014.

[8]    Huang, S., Vanmeensel, K., Van der Biest, O., and Vleugels, J., “In Situ Synthesis and Densification of Submicrometer-Grained B₄C–TiB₂ Composites by Pulsed Electric Current Sintering”, Journal of the European Ceramic Society, Vol. 31, No. 4, 2011, 637-644.

[9]    Itoh H, Tsunekawa Y, Tago S-i, and Iwahara H., “Synthesis and Sinterability of Composite Powder of the TiB₂-B₄C Systemˮ, Journal of alloys and compounds, Vol. 191, No. 2, 1993, pp. 191-195.

[10] Pierre, A. C., “Introduction to Sol-Gel Processing”, Springer, 1998.

[11] Yue, X., Zhao, S., Lü, P., Chang, Q., and Ru, H., “Synthesis and Properties of Hot Pressed B₄C–TiB₂ Ceramic Composite”, Materials Science and Engineering: A, Vol. 527, No. 27, 2010, pp. 7215-7219.