Investigating the Effect of Stiffness/Thickness Ratio on the Optimal Location of Piezoelectric Actuators Through PSO Algorithm

Journal of Solid Mechanics

مقاله 12، دوره 9، شماره 4، اسفند 2017، صفحه 832-848   

نوع مقاله: Research Paper

نویسندگان

S Jafari Fesharaki^{* 1}؛ S.Gh Madani²؛ S Golabi²

¹Department of Mechanical Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Iran

²Department of Mechanical Engineering, Faculty of Engineering, University of Kashan, Kashan, Iran

چکیده

This article has studied the effect of ratio of stiffness and thickness between piezoelectric actuators and host plat has been explored on optimal pattern for placement of piezoelectric work pieces around a hole in thin isotropic plate under static loading to reduce stress concentration. The piezoelectric actuators reduce directly or indirectly the stress concentration by applying positive and negative strains on the host plate. For this purpose, various modes as the thickness/stiffness ratios of the plate to the piezoelectric patches as ≥1 or ≤1 were considered. Then, a Python code was developed using particle swarm optimization algorithm in order to achieve the best model of piezoelectric actuators around the hole for maximum reduction in stress concentration factor. Also, the maximum stress concentration on the top and bottom of the hole was moved to another point around the edge by changing the location of piezoelectric patches. The results obtained from software solutions were confirmed by experimental tests. 

کلیدواژه‌ها

Optimization؛ Piezoelectric patches؛ Stiffness؛ particle swarm optimization

مراجع

[1] Wang Q., Wu N., 2012, A review on structural enhancement and repair using piezoelectric materials and shape memory alloys, Smart Materials and Structures 21(1): 013001.
[2] Kang Z., Tong L., 2008, Topology optimization-based distribution design of actuation voltage in static shape control of plates, Computers & Structures 86(19): 1885-1893.
[3] Kang Z., Wang X., Luo Z., 2012, Topology optimization for static shape control of piezoelectric plates with penalization on intermediate actuation voltage, Journal of Mechanical Design 134(5): 051006.
[4] Mehrabian A. R., Yousefi-Koma A., 2011, A novel technique for optimal placement of piezoelectric actuators on smart structures, Journal of the Franklin Institute 348(1): 12-23.
[5] Huang B., Kim H. S., 2014, Control of free-edge interlaminar stresses in composite laminates using piezoelectric actuators, Smart Materials and Structures 23(7): 074002.
[6] Platz R., Stapp C., Hanselka H., 2011, Statistical approach to evaluating active reduction of crack propagation in aluminum panels with piezoelectric actuator patches, Smart Materials and Structures 20(8): 085009.
[7] Wu N., Wang Q., 2011, An experimental study on the repair of a notched beam subjected to dynamic loading with piezoelectric patches, Smart Materials and Structures 20(11): 115023.
[8] Nguyen Q., Tong L., Gu Y., 2007, Evolutionary piezoelectric actuators design optimisation for static shape control of smart plates, Computer Methods in Applied Mechanics and Engineering 197(1): 47-60.
[9] Nguyen Q., Tong L., 2007, Voltage and evolutionary piezoelectric actuator design optimisation for static shape control of smart plate structures, Materials & Design 28(2): 387-399.
[10] Nguyen Q., Tong L., 2004, Shape control of smart composite plate with non-rectangular piezoelectric actuators, Composite Structures 66(1): 207-214.
[11] Hsu J. C., Tseng C. T., Chen Y. S., 2014, Analysis and experiment of self-frequency-tuning piezoelectric energy harvesters for rotational motion, Smart Materials and Structures 23(7): 075013.
[12] Sridharan S., Kim S., 2009, Piezo-electric control of stiffened panels subject to interactive buckling, International Journal of Solids and Structures 46(6): 1527-1538.
[13] Correia V. M. F., Soares C. M. M., Soares C. A. M., 2003, Buckling optimization of composite laminated adaptive structures, Composite Structures 62(3): 315-321.
[14] Chee C. Y. K., Tong L., Steven G. P., 2002, Static shape control of composite plates using a slope-displacement-based algorithm, AIAA Journal 40(8): 1611-1618.
[15] Lin J. C., Nien M., 2007, Adaptive modeling and shape control of laminated plates using piezoelectric actuators, Journal of Materials Processing Technology 189(1): 231-236.
[16] Zhang H., Lennox B., Goulding P. R., Leung A. Y., 2000, A float-encoded genetic algorithm technique for integrated optimization of piezoelectric actuator and sensor placement and feedback gains, Smart Materials and Structures 9(4): 552.
[17] Qing G., Qiu J., Liu Y., 2006, A semi-analytical solution for static and dynamic analysis of plates with piezoelectric patches, International Journal of Solids and Structures 43(6): 1388-1403.
[18] Da Mota Silva S., Ribeiro R., Rodrigues J. D., Vaz M., Monteiro J., 2004, The application of genetic algorithms for shape control with piezoelectric patches—an experimental comparison, Smart Materials and Structures 13(1): 220.
[19] Nakasone P. H., Silva E. C. N., 2010, Dynamic design of piezoelectric laminated sensors and actuators using topology optimization, Journal of Intelligent Material Systems and Structures 21(16): 1627-1652.
[20] Rafiee M., He X., Liew K., 2014, Nonlinear analysis of piezoelectric nanocomposite energy harvesting plates, Smart Materials and Structures 23(6): 065001.
[21] Roy T., Chakraborty D., 2009, Optimal vibration control of smart fiber reinforced composite shell structures using improved genetic algorithm, Journal of Sound and Vibration 319(1): 15-40.
[22] Wu N., Wang Q., 2010, Repair of vibrating delaminated beam structures using piezoelectric patches, Smart Materials and Structures 19(3): 035027.
[23] Kumar R., Mishra B., Jain S., 2008, Static and dynamic analysis of smart cylindrical shell, Finite Elements in Analysis and Design 45(1): 13-24.
[24] Quintero A. V., Besse N., Janphuang P., Lockhart R., Briand D., De Rooij N. F., 2014, Design optimization of vibration energy harvesters fabricated by lamination of thinned bulk-PZT on polymeric substrates, Smart Materials and Structures 23(4): 045041.
[25] Kurata M., Li X., Fujita K., Yamaguchi M., 2013, Piezoelectric dynamic strain monitoring for detecting local seismic damage in steel buildings, Smart Materials and Structures 22(11): 115002.
[26] Jadhav P. A., Bajoria K. M., 2013, Free and forced vibration control of piezoelectric FGM plate subjected to electro-mechanical loading, Smart Materials and Structures 22(6): 065021.
[27] Sensharma P. K., Haftka R. T., 1996, Limits of stress reduction in a plate with a hole using piezoelectric actuators, Journal of Intelligent Material Systems and Structures 7(4): 363-371.
[28] Sensharma P. K., Palantera M. J., Haftka R. T., 1993, Stress reduction in an isotropic plate with a hole by applied induced strains, Journal of Intelligent Material Systems and Structures 4(4): 509-518.
[29] Shah D., Joshi S., Chan W., 1994, Stress concentration reduction in a plate with a hole using piezoceramic layers, Smart Materials and Structures 3(3): 302.
[30] Fesharaki J. J., Golabi S., 2015, Optimum pattern of piezoelectric actuator placement for stress concentration reduction in a plate with a hole using particle swarm optimization algorithm, Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science 229(4): 614-628.
[31] Eberhart R., Kennedy J., A new optimizer using particle swarm theory, Proceeding of IEEE, Nagoya, Japan.
[32] Rao S. S., Rao S., 2009, Engineering Optimization: Theory and Practice, John Wiley & Sons.