Experimental Investigation of the Effects of the Roller Burnishing Parameters on the Surface Roughness and Micro-hardness of Ti6Al4V Alloy

Journal of Modern Processes in Manufacturing and Production

مقاله 10، دوره 8، شماره 3، آبان 2019، صفحه 57-66   

نوع مقاله: Research Paper

نویسندگان

Mohammad Asadbeiki^{1، 2}؛ Reza Nosouhi^{* 1، 2}

¹Modern Manufacturing Technologies Research Center, Najafabad Branch, Islamic Azad University, Najafabad, Iran

²Department of Mechanical Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Iran

چکیده

In this research, the effects of three important input parameters of roller burnishing process, namely burnishing speed, feed rate and the number of passes on the surface integrity (surface roughness and surface micro-hardness) of Ti-6Al-4V alloy are investigated. The design of the experiment is carried out using a full factorial method. Measurement of process outputs is carried out with precise methods and the results are recorded and examined. The results showed that the parameters studied have a very significant effect on the surface roughness and micro-hardness of Ti6Al4V alloy. The feed rate is the most effective parameter on the surface roughness and the burnishing speed is the most effective parameter on the surface micro-hardness. Generally concluded, the roller burnishing process improves the final surface quality and increases surface micro-hardness. It also concluded that increasing the number of the burnishing passes from 1 to 2 would excel both of the output parameters while increasing of this parameter further has no significant effect or; in certain cases; an inverse effect on the surface roughness and surface micro-hardness.

کلیدواژه‌ها

Roller Burnishing؛ Surface Roughness؛ Surface Hardness؛ Burnishing Speed؛ Burnishing Feed Rate

مراجع

[1] Rodríguez, A., López de Lacalle, L.N., Celaya, A., Lamikiz, A., Albizuri, J. 2012. Surface improvement of shafts by the deep ball-burnishing technique. Surface and Coatings Technology. 206 (11–12): 2817-2824.

[2] El-Tayeb, N.S.M., Low, K.O., and Brevern P.V. 2007. Influence of roller burnishing contact width and burnishing orientation on surface quality and tribological behaviour of Aluminium 6061. Journal of Materials Processing Technology. 186(1–3): 272-278.

[3] El-Axir, M.H. and El-Khabeery, M.M. 2003. Influence of orthogonal burnishing parameters on surface characteristics for various materials. Journal of Materials Processing Technology. 132(1–3): 82-89.

[4] Luo, H., Liu, J., Wang, L., and Zhong, Q. 2006. The effect of burnishing parameters on burnishing force and surface microhardness. The International Journal of Advanced Manufacturing Technology. 28(7): 707-713.

[5]  Revankar, G.D., Shetty, R., Rao, S.S., Gaitonde, V.N. 2016. Wear resistance enhancement of titanium alloy (Ti–6Al–4V) by ball burnishing process. Journal of Materials Research and Technology. 6 (1): 13-32.

[6] Chomienne, V., Valiorgue, F., Rech, J., Verdu, C. 2016. Influence of ball burnishing on residual stress profile of a 15-5PH stainless steel. CIRP Journal of Manufacturing Science and Technology. 13: 90-96.

[7] Yen, Y.C., Sartkulvanich, P., and Altan, T. 2005. Finite Element Modeling of Roller Burnishing Process. CIRP Annals. 54 (1): 237-240.

[8] Klocke, F., Liermann, J. 1998. Roller burnishing of hard turned surfaces. International Journal of Machine Tools and Manufacture. 38 (5–6): 419-423.

[9] Sartkulvanich, P., Altan, T., Jasso, F. and Rodriguez, C. 2007. Finite Element Modeling of Hard Roller Burnishing: An Analysis on the Effects of Process Parameters Upon Surface Finish and Residual Stresses. Journal of Manufacturing Science And Engineering, 129(4): 705-716.

[10] Klocke, F., Bäcker, V., Wegner, H. and Zimmermann, M. 2010. Finite Element Analysis of the Roller Burnishing Process for Fatigue Resistance Increase of Engine Components. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture. 225 (1): 2-11.