Edible Film Based on Lallemantia peltata L. Seed Gum: Development and Characterization

Journal of Chemical Health Risks

مقاله 6، دوره 12، شماره 1، فروردین 2022، صفحه 47-61   

نوع مقاله: Original Article

شناسه دیجیتال (DOI): 10.22034/jchr.2020.1896596.1118

نویسندگان

Anna Abdolshahi¹؛ Mojtaba Heydari Majd²؛ Mehdi Abdollahi³؛ Saeideh Fatemizadeh⁴؛ Leila Monjazeb Marvdashti^{* 1}

¹Food Safety Research Center (salt), Semnan University of Medical Sciences, Semnan, Iran

²Zabol University of Medical Sciences, Zabol, Iran

³Department of Biology and Biological Engineering – Food and Nutrition Science, Chalmers University of Technology, SE 412 96 Gothenburg, Sweden

⁴Department of Food Science and Technology, Ferdowsi University of Mashhad (FUM), Mashhad, Iran

چکیده

A novel edible film was developed using Lallemantia peltata (L.) seed gum (LSG), and its water sensitivity, physico-mechanical, barriers, microstructural and thermal properties as a function of glycerol concentration (20, 30, 40, 50 and 60% w/w) were studied. Different models were also used to investigate the water sorption of the LSG films. Unplasticized LSG films were brittle and difficult to handle which were effectively modified by glycerol addition. Water sensitivity, oxygen permeability, and elongation of LSG films were increased with increasing glycerol concentration. Also, increasing of glycerol concentration resulted in reduction of tensile strength, glass transition temperature (Tg) and melting temperature (Tm) of the films. Electron scanning micrographs revealed a smooth surfaceand compact cross-section microstructure in LSG films.The films showed sigmoid shape type II water sorption isotherms, representing typical features of most of biopolymers. Accordingly, the results suggest that LSG films containing desired glycerol concentration could potentially be used as edible films in food packaging.

کلیدواژه‌ها

Edible films؛ Lallemantia Peltata (L.)؛ Seed gum؛ Thermomechanical properties؛ Plasticizer

مراجع

1. Heydari-Majd M., Ghanbarzadeh B., Shahidi-Noghabi M., Najafi M.A., Adun P., Ostadrahimid A.J.P.T., 2019. Kinetic release study of zinc from polylactic acid based nanocomposite into food simulants. Polymer Testing. 1;76, 254-60.
2. Marvdashti L.M., Koocheki A., Yavarmanesh M.J.C.P., 2017. Alyssum homolocarpum seed gum-polyvinyl alcohol biodegradable composite film: Physicochemical, mechanical, thermal and barrier properties. Carbohydrate Polymers. 155, 280-293.
3. Heydari-Majd M., Ghanbarzadeh B., Shahidi-Noghabi M., Najafi M.A., Hosseini M.J.F.P., Life S., 2019. A new active nanocomposite film based on PLA/ZnO nanoparticle/essential oils for the preservation of refrigerated Otolithes ruber fillets. Food Packaging and Shelf Life.19, 94-103.
4. Marvdashti L.M., Koocheki A., Yavarmanesh M.J.F.B., 2019. Characterization, Release Profile and Antimicrobial Properties of Bioactive Polyvinyl Alcohol-Alyssum homolocarpum Seed Gum-Nisin Composite Film. Food Biophysics. 15;14(2), 120-31
5. Abdolshahi A., Marvdashti L.M., Salehi B., Sharifi‐Rad M., Ghobakhloo S., Iriti M., Sharifi‐Rad J., 2019. Antifungal activities of coating incorporated with Saccharomyces cerevisiae cell wall mannoprotein on Aspergillus flavus growth and aflatoxin production in pistachio (Pistacia vera L.). Journal of Food Safety. 39(2), e12608.
6. Abdolshahi A., Tabatabaei Yazdi F., Shabani A.,

 

 

Mortazavi S., 2019. Active gelatin-mannan film: physicochemical, antifungal and aflatoxin binding properties. International Food Research Journal. 26(6), 1803-1812.

7. Monjazeb Marvdashti L, Abdulmajid Ayatollahi S, Salehi B, Sharifi‐Rad J, Abdolshahi A, Sharifi‐Rad R, Maggi F, 2020. Optimization of edible Alyssum homalocarpum seed gum‐chitosan coating formulation to improve the postharvest storage potential and quality of apricot (Prunus armeniaca L.). Journal of Food Safety:e12805.
8. Ahmadi R., Kalbasi-Ashtari A., Oromiehie A., Yarmand M.S., Jahandideh F., 2012. Development and characterization of a novel biodegradable edible film obtained from psyllium seed (Plantago ovata Forsk). Journal of Food Engineering. 109(4), 745-751.
9. Antoniou J., Liu F., Majeed H., Qazi H.J., Zhong F., 2014. Physicochemical and thermomechanical characterization of tara gum edible films: effect of polyols as plasticizers. Carbohydrate Polymers. 111, 359-365.
10. Khazaei N., Esmaiili M., Djomeh Z.E., Ghasemlou M., Jouki M., 2014. Characterization of new biodegradable edible film made from basil seed (Ocimum basilicum L.) gum. Carbohydrate Polymers. 102, 199-206.
11. Moreira B.R., Batista K.A., Castro E.G., Lima E.M., Fernandes K.F., 2015. A bioactive film based on cashew gum polysaccharide for wound dressing applications. Carbohydrate polymers. 122, 69-76.
12. Seyedi S., Koocheki A., Mohebbi M., Zahedi Y., 2014. Lepidium perfoliatum seed gum: A new source of carbohydrate to make a biodegradable film. Carbohydrate Polymers. 101, 349-358.
13. Ghannadi A., Zolfaghari B., 2003. Compositional analysis of the essential oil of Lallemantia royleana (Benth. in Wall.) Benth. from Iran. Flavour and Fragrance Journal. 18(3), 237-239.
14. Moghaddam T.M., Razavi S., Emadzadeh B., 2011. Rheological interactions between Lallemantia royleana seed extract and selected food hydrocolloids. Journal of the Science of Food and Agriculture. 91(6), 1083-1088.
15. Mohammad Amini A., 2007. Extraction optimization of Balangu seed gum and effect of Balangu seed gum on the rheological and sensory properties of Iranian flat bread (Doctoral dissertation, MSc thesis, Ferdowsi University of Mashhad, Iran), 14-28.
16. Amini A.M., Razavi S.M., 2012. Dilute solution properties of Balangu (Lallemantia royleana) seed gum: Effect of temperature, salt, and sugar. International Journal of Biological Macromolecules. 51(3), 235-243.
17. Najafi M.N., Hosaini V., Mohammadi-Sani A., Koocheki A., 2016. Physical stability, flow properties and droplets characteristics of Balangu (Lallemantia royleana) seed gum/whey protein stabilized submicron emulsions. Food Hydrocolloids. 59, 2-8.
18. Baldwin E. A., Hagenmaier R., Bai J., 2011. Edible coatings and films to improve food quality. CRC Press. Book. Aug 24. 17-36
19. Salehi F., Kashaninejad M., Behshad V., 2014. Effect of sugars and salts on rheological properties of Balangu seed(Lallemantia royleana) gum. International Journal of Biological Macromolecules. 67 16-21.
20. Farahnaky A., Ansari S., Majzoobi M., 2009. Effect of glycerol on the moisture sorption isotherms of figs. Journal of Food Engineering. 93(4), 468-473.
21. Berg C., Bruin S., 1981. Water activity and its estimation in food systems: theoretical aspects. In Rockland LB, Stewart GF, editors, Water activity: Influences on food quality. New York: Academic Press. 2-61.
22. Oswin C., 1946. The kinetics of package life. III. The isotherm. Journal of Chemical Technology and Biotechnology. 65 (12), 419-421.
23. Bonilla J., Fortunati E., Atarés L., Chiralt A., Kenny J.M., 2014. Physical, structural and antimicrobial properties of poly vinyl alcohol–chitosan biodegradable films. Food Hydrocolloids. 35, 463-470.
24. Shojaee-Aliabadi S., Hosseini H., Mohammadifar M.A., Mohammadi A., Ghasemlou M., Ojagh S.M., Hosseini S.M., Khaksar R., 2013. Characterization of antioxidant-antimicrobial κ-carrageenan films containing Satureja hortensis essential oil. International Journal of Biological Macromolecules. 52, 116-124.
25. ASTM E., 1995. Standard test methods for water vapor transmission of materials. Foundation drainage rate: Hydraulic Gradient, 1, 18.
26. ASTMD3985-81, 2002. D3985-81. Oxygen gas transmission rate through plastic film and sheeting using a coulometric sensor.
27. ASTM D., 2002. 882-02. Standard test method for tensile properties of thin plastic sheeting.
28. Sadeghi-Varkani A., Emam-Djomeh Z., Askari G., 2018. Physicochemical and microstructural properties of a novel edible film synthesized from Balangu seed mucilage. InternationalJournal of Biological Macromolecules. 108, 1110-1119.
29. Razavi S.M.A., Amini A.M., Zahedi Y., 2015. Characterisation of a new biodegradable edible film based on sage seed gum: Influence of plasticiser type and concentration. Food Hydrocolloids. 43, 290-298.
30. Jouki M., Khazaei N., Ghasemlou M., HadiNezhad M., 2013. Effect of glycerol concentration on edible film production from cress seed carbohydrate gum. Carbohydrate Polymers. 96 (1), 39-46.
31. Haq M.A., Hasnain A., Azam M., 2014. Characterization of edible gum cordia film: Effects of plasticizers. LWT-Food Science and Technology. 55(1), 163-169.
32. Jouki M., Yazdi F.T., Mortazavi S.A., Koocheki A., 2013. Physical, barrier and antioxidant properties of a novel plasticized edible film from quince seed mucilage. International Journal of Biological Macromolecules. 62, 500-507.
33. Su J.F., Huang Z., Zhao Y.H., Yuan X.Y., Wang X.Y., Li M., 2010. Moisture sorption and water vapor permeability of soy protein isolate/poly (vinyl alcohol)/glycerol blend films. Industrial Crops and Products. 31 (2), 266-276.
34. Ghanbarzadeh B., Almasi H., 2011. Physical properties of edible emulsified films based on carboxymethyl cellulose and oleic acid. International journal of biological Macromolecules. 48(1), 44-49.
35. Zhang Y., Han J., 2008. Sorption isotherm and plasticization effect of moisture and plasticizers in pea starch film. Journal of Food Science. 73(7), E313-24.
36. Brunauer S., Emmett P.H., Teller E., 1938. Adsorption of gases in multimolecular layers. Journal of the American Chemical Society. 60 (2), 309-319.
37. Cho S.Y., Rhee C., 2002. Sorption characteristics of soy protein films and their relation to mechanical properties. LWT-Food Science and Technology. 35(2), 151-157.
38. Rachtanapun P., Suriyatem R., 2012. Moisture sorption isotherms of soy protein isolate/carboxymethyl chitosan blend films. Journal of Agricultural Science and Technology. A, 2 (1A), 50.
39. Suppakul P., Chalernsook B., Ratisuthawat B., Prapasitthi S., Munchukangwan N., 2013. Empirical modeling of moisture sorption characteristics and mechanical and barrier properties of cassava flour film and their relation to plasticizing–antiplasticizing effects. LWT-Food Science and Technology. 50 (1), 290-297.
40. Suppakul P., 2006. Moisture sorption characteristics of cassava flour film. InProceedings of 15th IAPRI World Conference on Packaging. 1,1-13.
41. Ramos Ó.L., Reinas I., Silva S.I., Fernandes J.C., Cerqueira M.A., Pereira R.N., Vicente A.A., Poças M.F., Pintado M., Malcata F.X., 2013. Effect of whey protein purity and glycerol content upon physical properties of edible films manufactured therefrom. Food Hydrocolloids. 30(1), 110-122.
42. Slavutsky A.M., Bertuzzi M.A., Armada M., García M.G., Ochoa N.A., 2014. Preparation and characterization of montmorillonite/brea gum nanocomposites films. Food Hydrocolloids. 35, 270-278.
43. Ghanbarzadeh B., Oromiehie A., Musavi M., Falcone P.M., Rad E.R., 2007. Study of mechanical properties, oxygen permeability and AFM topography of zein films plasticized by polyols. Packaging Technology and Science. 20(3), 155-163.
44. Monjazeb Marvdashti L., Yavarmanesh M., Koocheki A., 2016. The Effect of Different Concentrations of Glycerol on Properties of Blend Films Based on Polyvinyl Alcohol-AllysumHomolocarpum Seed Gum. Iranian Food Science and Technology Research Journal. 12(5), 663-677.
45. Marvdashti L.M., Koocheki A., Yavarmanesh M., 2017. Alyssum homolocarpum seed gum-polyvinyl alcohol biodegradable composite film: Physicochemical, mechanical, thermal and barrier properties. Carbohydrate Polymers. 155, 280-293.
46. Müller C.M., Yamashita F., Laurindo J.B., 2008. Evaluation of the effects of glycerol and sorbitol concentration and water activity on the water barrier properties of cassava starch films through a solubility approach. Carbohydrate Polymers. 72(1), 82-87.
47. Wang Y., Li D., Wang L.j., Yang L., Özkan N., 2011. Dynamic mechanical properties of flaxseed gum based edible films. Carbohydrate Polymers. 86(2), 499-504.
48. Jia D., Fang Y., Yao K., 2009. Water vapor barrier and mechanical properties of konjac glucomannan–chitosan–soy protein isolate edible films. Food and Bioproducts Processing. 87(1), 7-10.
49. Gaudin S., Lourdin D., Forssell P., Colonna P., 2000. Antiplasticisation and oxygen permeability of starch–sorbitol films. Carbohydrate Polymers. 43(1), 33-37.
50. McHugh T.H., Krochta J.M., 1994. Milk-protein-based edible films and coatings. Food Technology.48(1), 97-103.
51. Di Pierro P., Sorrentino A., Mariniello L., Giosafatto C.V.L., Porta R., 2011. Chitosan/whey protein film as active coating to extend Ricotta cheese shelf-life. LWT-Food Science and Technology. 44(10), 2324-2327.
52. Liu H., Adhikari R., Guo Q., Adhikari B., 2013. Preparation and characterization of glycerol plasticized (high-amylose) starch–chitosan films. Journal of Food Engineering. 116(2), 588-597.
53. Pongjanyakul T., Puttipipatkhachorn S., 2007. Alginate-magnesium aluminum silicate films: Effect of plasticizers on film properties, drug permeation and drug release from coated tablets. International Journal of Pharmaceutics. 333(1), 34-44.
54. Mali S., Grossmann M.V.E., Garcı́a M.A., Martino M.N., Zaritzky N.E., 2004. Barrier, mechanical and optical properties of plasticized yam starch films. Carbohydrate Polymers. 56(2), 129-135.
55. Kurt A., Kahyaoglu T., 2014. Characterization of a new biodegradable edible film made from salep glucomannan. Carbohydrate Polymers. 104, 50-58.
56. Wilhelm H.M., Sierakowski M.R., Souza G., Wypych F., 2003. Starch films reinforced with mineral clay. Carbohydrate Polymers. 52(2), 101-110.