Influences of Blank Holder Force in The Multi-Step Deep Drawing Process of Aluminum Sheets

ADMT Journal

دوره 13، شماره 3، آذر 2020، صفحه 51-57   

نوع مقاله: Original Article

شناسه دیجیتال (DOI): 10.30495/admt.2020.1880364.1147

نویسندگان

Sajad Bakhtiari¹؛ Seyed Jalal Hashemi^{* 2}؛ Amir Hossein Roohi³

¹Department of Mechanical Engineering, Shahid Rajaee Teacher Training University, Tehran, Iran

²Department of Mechanical Engineering, Faculty of Enghelab-e Eslami, Tehran Branch, Technical and Vocational University (TVU), Tehran, Iran

³Department of Mechanical Engineering, Faculty of Industrial and Mechanical Engineering, Qazvin Branch, Islamic Azad University, Qazvin, Iran

چکیده

In recent decades, the use of aluminium alloys is developed in the automotive industry with regard to the need for lightweight and anti-corrosion components, one of which is AA7075 Al alloy. In this study, the multi-step deep drawing process of AA7075 aluminium sheets under various blank holder forces is investigated through a numerical simulation and is then validated with experimental results. Simulations were conducted by ABAQUS finite element software, and the influences of the blank holder force on the wrinkling height, rupture occurrence and thickness distribution of the sheet were studied. The optimum amount of blank holder force at each drawing step is determined so that the height of wrinkling, and the thinning percentage do not exceed the permissible value. Based on the results, the blank holder force magnitude should be considered descending during the four successive steps to achieve more uniform thickness distribution, and also the wrinkling height could be reduced by increasing the blank holder force in the analysed force range. The optimum amount of blank holder force in the four drawing steps was 28000, 2500, 1500 and 600 N, respectively. In general, the minimum thickness was created in the corner of the punch. The results also showed that an excessive increase in the blank holder force in order to eliminate the wrinkling caused the thinning percentage to increase. Finally, a good accordance between the experimental and numerical results was observed.

کلیدواژه‌ها

Blank Holder Force؛ Deep Drawing؛ Finite Element Analysis؛ Thickness Distribution

مراجع

[1]     Koc, M., Altan, T., An Overall Review of the Tube Hydroforming (THF) Technology, Journal of Materials Processing Technology, Vol. 108, No. 3, 2001, pp. 384-393.

[2]     Colgan, M., Monaghan, J., Deep Drawing Process: Analysis and Experiment, Journal of Materials Processing Technology, Vol 132, No. 1-3, 2003, pp. 35-41.

[3]     Vollertsen, F., Prange, T., and Sander, M., Hydroforming: Needs, Developments and Perspectives, Advanced Technology of Plasticity, Vol. 2, No. 1, 1999, pp. 1197-1209.

[4]     Hashemi, S. J., Naeini, H. M., Liaghat, G., Karami, J. S., and Roohi, A. H., Prediction of Bursting in Warm Tube Hydroforming using Modified Ductile Fracture Criteria, Modares Mechanical Engineering, Vol. 14, No. 16, 2015, pp. 201-211.

[5]     Choi, T., Choi, S., Na, K., and Bae, H., Chung W, Application of Intelligent Design Support System for Multi-Step Deep Drawing Process, Journal of Materials Processing Technology, Vol. 130, No. 1, 2002, pp. 76-88.

[6]     Sheng, Z., Taylor, R., and Strazzanti, M., FEM-Based Progressive Drawing Process Design, The International Journal of Advanced Manufacturing Technology, Vol. 36, No. 3-4, 2008, pp. 226-36.

[7]     Li, W., Meng, B., Wang, C., Wan, M., and Xu, L., Effect of Pre-Forming and Pressure Path On Deformation Behavior in Multi-Pass Hydrodynamic Deep Drawing Process, International Journal of Mechanical Sciences, Vol. 121, No. 1, 2017, pp. 171-180.

[8]     Sivasankaran, S., Narayanasamy, R., Jeyapaul, R., and Loganathan, C., Modelling of Wrinkling in Deep Drawing of Different Grades of Annealed Commercially Pure Aluminium Sheets When Drawn Through a Conical Die Using Artificial Neural Network, Materials & Design, Vol. 30, No. 8, 2009, pp. 3193-3205.

[9]     Tikhovskiy, I., Raabe, D., and Roters, F., Simulation of Earing During Deep Drawing of an Al–3% Mg Alloy (AA 5754) Using a Texture Component Crystal Plasticity FEM, Journal of Materials Processing Technology, Vol. 183, No. 2-3, 2007, pp. 169-175.

[10]  Liu, W., Chen, B. K., Sheet Metal Anisotropy and Optimal Non-Round Blank Design in High-Speed Multi-Step Forming of AA3104-H19 Aluminium Alloy Can Body, The International Journal of Advanced Manufacturing Technology, Vol. 95, No. 9-12, 2018, pp. 4265-4277.

[11]  Qayyum, F., Shah, M., Muqeet, A., and Afzal, J., The Effect of Anisotropy On the Intermediate and Final Form in Deep Drawing of Ss304l, With High Draw Ratios: Experimentation and Numerical Simulation, IOP Conference Series: Materials Science and Engineering, Vol. 146, No. 1, 2016, pp. 012031

[12]  Proubet, J., Baudelet, B., Rupture Criteria During Deep Drawing of Aluminum Alloys, Studies in Applied Mechanics, Vol. 45, No. 1, 1997, pp. 289-297.

[13]  Zhang, W., Tor, S., and Britton, G., Indexing and Retrieval in Case-Based Process Planning for Multi-Stage Non-Axisymmetric Deep Drawing, The International Journal of Advanced Manufacturing Technology, Vol. 28, No. 1-2, 2006, pp. 12-22.

[14]  Abdelmaguid, T. F., Abdel-Magied, R. K., Shazly, M., and Wifi, A. S., A Dynamic Programming Approach for Minimizing the Number of Drawing Stages and Heat Treatments in Cylindrical Shell Multistage Deep Drawing, Computers & Industrial Engineering, Vol. 66, No. 3, 2013, pp. 525-532.

[15]  Pacheco, M., Celentano, D., García-Herrera, C., Méndez, J., and Flores, F., Numerical Simulation and Experimental Validation of a Multi-Step Deep Drawing Process, International Journal of Material Forming, Vol. 10, No. 1, 2017, pp. 15-27.

[16]  Brown, W. F., Mindlin, H., and Ho, C. Y., Aerospace Structural Metals Handbook: CINDAS/USAF CRDA Handbooks Operation, Purdue University, West Lafayette, USA, Code 3206, Vol. 3, 1996.

[17]  Sheng, Z., Jirathearanat, S., and Altan, T., Adaptive FEM Simulation for Prediction of Variable Blank Holder Force in Conical Cup Drawing, International Journal of Machine Tools and Manufacture, Vol. 44, No. 5, 2004, pp. 487-494.