Fatigue Crack Growth in Plastically Compressible Solids: Role of Negative Stress Ratio, Plastic Compressibility and Strain Softening

Journal of Solid Mechanics

مقاله 12، دوره 12، شماره 4، اسفند 2020، صفحه 902-911   

نوع مقاله: Research Paper

شناسه دیجیتال (DOI): 10.22034/jsm.2020.1899251.1587

نویسندگان

Y Mittal؛ D Khan^* ؛ S Pandey؛ G.Chand Gupta

Department of Mechanical Engineering, Indian Institute of Thechnology Varansi, Varansi, India

چکیده

The effect of cyclic loading on fatigue crack growth in plastically compressible solids is investigated at negative stress ratio under plane strain and small scale yielding conditions. The material is characterized by a finite strain elastic viscoplastic constitutive model with hardening and hardening-softening-hardening hardness functions. Displacements corresponding to the isotropic linear elastic mode I crack field are prescribed on a remote boundary. The plastic crack growth, crack tip opening displacement (CTOD) and near crack tip stress fields are presented using finite element method. Material hardening/ softening has a major relevance on crack growth, CTOD and the evolution of stress distribution. It is revealed here that the negative stress ratio can significantly influence the loading conditions at the crack tip and thereby increase the crack growth for tension–compression loading for hardening material whereas the fatigue crack growth of plastically compressible hardening-softening-hardening material is only slightly affected by the negative stress ratio albeit it is accepted in literature that compressive loads contribute to fatigue crack growth significantly. In the present studies, the CTOD variation with applied load and the near stress distribution are also very unusual in nature.  

کلیدواژه‌ها

Compressible solids؛ Fatigue crack growth؛ Finite element method؛ Material softening؛ Negative stress ratio

مراجع

[1] Carlson R.L., Kardomateas G.A., 1994, Effects of compressive load excursions on fatigue crack growth, International Journal of Fatigue 16: 141-146.
[2] Silva F.S., 2005, The importance of compressive stress ratio on fatigue crack propagation, International Journal of Fatigue 27: 1441-1452.
[3] Zang J., He X.D., Sha Y., Du S.Y., 2010, The compressive stress effect on fatigue crack growth under tension-compression loading, International Journal of Fracture 32: 361-367.
[4] Bai S., Sha Y., Zhang J., 2018, The effect of compression loading on fatigue crack propagation after a single tensile overload at negative stress ratios, International Journal of Fatigue 110: 162-171.
[5] Benz C., 2018, Fatigue crack growth at negative stress ratios: on the uncertainty of using and R to define the cyclic crack tip load, Engineering Fracture Mechanics 189: 194-203.
[6] Hassanifard S., Bonab M.A., Mohtadi M., Jabbari G.h., 2013, Investigation of fatigue crack propagation in spot-welded joints based on fracture mechanics approach, Journal of Materials Engineering and Performance 22: 245-250.
[7] Bonab M.A., Mohtadi M., Eskandari M., Ghaednia H., Das S., 2016, Effect of microstructural parameters on fatigue crack propagation in an API x65 pipeline steel, Journal of Materials Engineering and Performance 25: 4933-4940.
[8] Rudnicki J. W., Rice J. R., 1975, Conditions for the localization of deformation in pressure-sensitive dilatant material, Journal of the Mechanics and Physics of Solids 23: 371-394.
[9] Spitzig W. A., Richmond O., 1979, Effect of hydrostatic pressure on the deformation behavior of polyethylene and polycarbonate in tension and compression, Polymer Engineering and Science 19(16): 1129-1139.
[10] McMeeking R.M., 1977, Finite deformation analysis of crack tip opening in elastic-plastic materials and implications for fracture, Journal of the Mechanics and Physics of Solids 25: 357-381.
[11] Hutchens S.B., Needleman A., Greer J.R., 2011, Analysis of uniaxial compression of vertically aligned carbon nanotubes, Journal of Mechanics and Physics of Solids 59: 2227-2237.
[12] Needleman A., Hutchens S.B., Mohan N., Greer J.R., 2012, Deformation of plastically compressible hardening–softening–hardening solids, Acta Mechanica Sinica 28: 1115-1124.
[13] Mohan N., Cheng J., Greer J.R., Needleman A., 2013, Uniaxial tension of a class of compressible solids with plastic non-normality, Journal of Applied Mechanics 80: 040912-1-8.
[14] Toribio J., Kharin V., 2009, Finite deformation analysis of crack tip fields under cyclic loading, International Journal of Solids and Structures 46(9): 1937-1952.
[15] Khan D., Singh S., Needleman A., 2017, Finite deformation analysis of crack tip fields in plastically compressible hardening-softening-hardening solids, Acta Mechanica Sinica 33(1): 148-158.
[16] Lai J., Van der Giessen E., 1997, A numerical study of crack-tip plasticity in glassy polymers, Mechanics of Materials 25: 183-197.
[17] Singh S., Khan D., 2018, On fatigue crack growth in plastically compressible hardening and hardening-softening-hardening solids using crack tip blunting, International Journal of Fracture 213: 139-155.
[18] Peirce D., Shih C.F., Needleman A., 1984, A tangent modulus method for rate dependent solids, Computers & Structures 18(5): 875-887.
[19] Liu N., Drugan W.J., 1993, Finite deformation finite element analyses of tensile growing crack fields in elastic-plastic material, International Journal of Fracture 61: 189-210.