Design, Modeling and Manufacturing a New Robotic Gripper with High Load Bearing Capability and Robust Control of its Mechanical Arm

ADMT Journal

دوره 14، شماره 1، خرداد 2021، صفحه 1-17   

نوع مقاله: Original Article

شناسه دیجیتال (DOI): 10.30495/admt.2021.1872367.1131

نویسندگان

vahid Boomeri؛ Hami Tourajizadeh^*

Department of Mechanical Engineering, Faculty of Engineering, University of Kharazmi, Tehran, Iran

چکیده

In this paper, a new robotic gripper is proposed and modeled which is able to bear a high amount of load and it can be used as the claws of climbing robots. As the climbing robots are usually heavy and their configuration should be kept in height against the gravity, firm grippers with no slippage possibility should be designed in order to guarantee the stability. The proposed new gripper is essentially required for the grip-based climbing robots which are heavy and are supposed to accomplish a specific operational task while they are grasping the pipe-shaped structures. The kinematic and quasi-static modeling of the proposed gripper is extracted and its related parameters are optimized to provide the maximum gripping force and the minimum slippage probability. Since these robust grippers are usually actuated by high torque motors, the reaction effect of the actuators force on the arm of the robot model is investigated here as a new study. Hence, the corresponding mechanical arm is also controlled, using a robust nonlinear controller to neutralize the destructive effect of extreme reaction forces or torques from the gripper motors to the robot arm during its mission. Thus, a robust controller is designed and implemented on the arm joint to cover the required positioning accuracy of the arm movement during the climbing motion. Afterward, the applicability of the proposed gripper and also the efficiency of the designed controller is verified by the aid of some analytic and comparative simulation scenarios performed in MATLAB-SIMULINK and MSC-ADAMS simulation. It is shown that the proposed gripper together with its related controlling algorithm for the arm can successfully provide a proper climbing mechanism for these kinds of robots which are supposed to climb through the structures and perform a special manipulating task.  

کلیدواژه‌ها

Climbing Robot؛ Gripper Mechanism؛ Optimal Design؛ Robust Controller؛ Sliding Mode Control

مراجع

[1]     Zhang, J., Fang, X., Challenges and Key Technologies in Robotic Cell Layout Design and Optimization, Proceedings of the Institution of Mechanical Engineers, Part C, Journal of Mechanical Engineering Science, Vol. 231, No. 15, 2017, pp. 2912-24.

[2]     Bicchi, A., Hands for Dexterous Manipulation and Robust Grasping: a Difficult Road Toward Simplicity, IEEE Transactions on Robotics and Automation, Vol. 16, No. 6, 2000, pp. 652-62.

[3]     Hsu, J., Yoshida, E., Harada, K., and Kheddar, A., Editors., Self-Locking Underactuated Mechanism for Robotic Gripper, 2017 IEEE International Conference on Advanced Intelligent Mechatronics (AIM), 2017, IEEE.

[4]     Rojas, N., Ma, R. R., and Dollar, A. M., The GR2 Gripper: an Underactuated Hand for Open-Loop in-Hand Planar Manipulation, IEEE Transactions on Robotics, Vol. 32, No. 3, 2016, pp. 763-70.

[5]     Puig, J. E. P., Rodriguez, N. E. N., and Ceccarelli, M., A Methodology for the Design of Robotic Hands with Multiple Fingers, International Journal of Advanced Robotic Systems, Vol. 5, No. 2, 2008, pp. 1-22.

[6]     Choi, M. S., Lee, D. H., Park, H., Kim, Y. J., Jang, G. R, and Shin, Y. D., et al., Editors., Development of Multi-Purpose Universal Gripper, 2017 56th Annual Conference of the Society of Instrument and Control Engineers of Japan (SICE), 2017, IEEE.

[7]     Takaki, T., Omata, T., High-Performance Anthropomorphic Robot Hand with Grasping-Force-Magnification Mechanism, IEEE/ASME Transactions on Mechatronics, Vol. 16, No. 3, 2010, pp. 583-91.

[8]     Liu, C. H., Chiu, C. H., Editors., Design and Prototype of Monolithic Compliant Grippers for Adaptive Grasping, 2018 3rd International Conference on Control and Robotics Engineering (ICCRE), 2018, IEEE.

[9]     Yi, B. J., Na, H. Y., Lee, J. H., Hong, Y. S., Oh, S. R., and Suh, I. H., et al., Design of a Parallel-Type Gripper Mechanism, The International Journal of Robotics Research, Vol. 21, No. 7, 2002, pp. 661-76.

[10]  Kocabas, H., Gripper Design with Spherical Parallelogram Mechanism, Journal of Mechanical Design, Vol. 131, No. 7, 2009, pp. 075001.

[11]  Jiang, L., Guan, Y., Zhou, X., Zhang, X., and Zhang, H., Editors., Grasping Analysis for a Biped Climbing Robot, 2010 IEEE International Conference on Robotics and Biomimetics, 2010, IEEE.

[12]  Tavakoli, M., Marques, L., 3DCLIMBER: Climbing and Manipulation Over 3D Structures, Mechatronics, Vol. 21, No. 1, 2011, pp. 48-62.

[13]  Mampel, J., Gerlach, K., Schilling, C., and Witte, H., A Modular Robot Climbing On Pipe-Like Structures, 4th International Conference on Autonomous Robots and Agents 2009, Feb 10 ,pp. 87-91, IEEE.

[14]  Abderrahim, M., Balaguer, C., Giménez, A., Pastor, J. M., and Padron, V. M., ROMA: A Climbing Robot for Inspection Operations, In Proceedings 1999 IEEE International Conference on Robotics and Automation, 1999, IEEE.

[15]  Nagaoka, K., Minote, H., Maruya, K., Shirai, Y., Yoshida, K., Hakamada, T., Sawada, H., and Kubota, T., Passive Spine Gripper for Free-Climbing Robot in Extreme Terrain, IEEE Robotics and Automation Letters, Vol. 3, No. 3, 2018, pp. 1765-70.

[16]  Rahman, N., Carbonari, L., Caldwell, D., and Cannella, F., Kinematic Analysis, Prototypation and Control of a Novel Gripper for Dexterous Applications, Journal of Intelligent & Robotic Systems, Vol. 91, No. 2, 2018, pp. 193-206.

[17]  Heidari, H., Pouria, M. J., Sharifi, S., and Karami, M., Design and Fabrication of Robotic Gripper for Grasping in Minimizing Contact Force, Advances in Space Research, Vol. 61, No. 5, 2018, pp. 1359-1370.

[18]  Bai, G., Kong, X., and Ritchie, J. M., Kinematic Analysis and Dimensional Synthesis of a Meso-Gripper, Journal of Mechanisms and Robotics, Vol. 9, No. 3, 2017, pp. 031017.

[19]  Borisov, I. I., Borisov, O. I., Gromov, V. S., Vlasov, S. M., Dobriborsci, D., and Kolyubin, S. A., Design of Versatile Gripper with Robust Control, IFAC-Papers On Line, Vol. 51, No. 22, 2018, pp. 56-61.

[20]  Slotine, J. J., Sastry, S. S., Tracking Control of Non-Linear Systems Using Sliding Surfaces, with Application to Robot Manipulators, International Journal of Control, Vol. 38, No. 2, 1983, pp. 465-92.

[21]  Slotine, J. J. E., The Robust Control of Robot Manipulators, The International Journal of Robotics Research, Vol. 4, No. 2, 1985, pp. 49-64.

[22]  Slotine, J. J. E., Li, W., On the Adaptive Control of Robot Manipulators, the International Journal of Robotics Research, Vol. 6, No. 3, 1987, pp. 49-59.

[23]  Huang, A. C., Chen, Y. C., Adaptive Sliding Control for Single-Link Flexible-Joint Robot with Mismatched Uncertainties, IEEE Transactions on Control Systems Technology, Vol. 12, No. 5, 2004, pp. 770-5.

[24]  Parra Vega, V., Arimoto, S., Liu, Y. H., Hirzinger, G., and Akella, P., Dynamic Sliding PID Control for Tracking of Robot Manipulators: Theory and Experiments, IEEE Transactions on Robotics and Automation,Vol. 19, No. 6, 2003, pp. 967-76.

[25]  Harashima, F., Hashimoto, H., and Maruyama, K., Editors., Practical Robust Control of Robot Arm Using Variable Structure System, Proceedings 1986 IEEE International Conference on Robotics and Automation, 1986, IEEE.

[26]  Talole, S., Phadke, S., Model Following Sliding Mode Control Based On Uncertainty and Disturbance Estimator, Journal of Dynamic Systems, Measurement, and Control, Vol. 130, No. 3, 2008, pp. 034501.

[27]  Young, K. D., Utkin, V. I., and Ozguner, U., Editors., A Control Engineer's Guide to Sliding Mode Control, Proceedings 1996 IEEE International Workshop on Variable Structure Systems-VSS'96, 1996, IEEE.

[28]  Slotine, J. J. E., Li, W., Applied Nonlinear Control: Prentice Hall Englewood Cliffs, NJ, 1991.

[29]  Asada, H., Slotine, J. J., Robot Analysis and Control, John Wiley & Sons, 1986.