تأثیر زمان اتصال بر ریزساختار و تکمیل انجماد ایزوترم در خلال اتصال TLP سوپر آلیاژهای پایه نیکل غیرمشابه IN738LC و Nimonic 75

فرآیندهای نوین در مهندسی مواد

دوره 15، شماره 2 - شماره پیاپی 57، تیر 1400، صفحه 13-25   

نوع مقاله: علمی-پژوهشی

شناسه دیجیتال (DOI): 10.30495/apme.2021.510140.1047

نویسندگان

میثم خاکیان قمی^{* 1}؛ محمد سعید شهریاری²؛ سعید ناطق³

¹دکتری مهندسی مواد و متالورژی، مدیر مهندسی بازسازی شرکت مهندسی موادکاران- مپنا، کرج، ایران.

²کارشناس ارشد مهندسی مواد و متالورژی، مدیر مهندسی بازسازی قطعات هوایی شرکت مهندسی موادکاران- مپنا، کرج، ایران.

³استاد، دانشگاه آزاد اسلامی، واحد علوم و تحقیقات، دانشکده مهندسی مواد و متالورژی، تهران، ایران.

چکیده

اتصال سوپر آلیاژهای پایه نیکل اینکونل 738 و نایمونیک 75 با استفاده از لایه واسط حاوی Ni-Cr-B و با نام تجاری MBF-80 توسط فرآیند فاز مایع گذرا (TLP) در دماهای ℃1080، ℃1120، ℃1150 و ℃1180 و زمان‌های مختلف انجام شد. ریزساختار اتصال با استفاده از میکروسکوپ الکترونی روبشی (SEM) و میکروسکوپ نوری مورد مطالعه قرار گرفت. بررسی‌های ریزساختاری نشان داد که در زمان‌های کوتاه اتصال، ریزساختار شامل فازهای بین فلزی یوتکتیکی پیوسته در خط مرکزی اتصال می‌باشد و با افزایش زمان اتصال در دمای ثابت به‌تدریج از پیوستگی آن کم و نهایتاً به‌طور کامل حذف می‌شوند. به‌منظور پیش‌بینی زمان لازم برای تکمیل انجماد ایزوترم از معادلات نفوذ فیک استفاده شد و مشاهده گردید که تطابق خوبی بین زمان پیش‌بینی شده برای تکمیل انجماد ایزوترم و نتایج تجربی وجود دارد.

کلیدواژه‌ها

سوپرآلیاژ نایمونیک 75 و اینکونل 738؛ اتصال TLP؛ ریزساختار؛ انجماد ایزوترم

مراجع

[1] O. A. Ojo, "On liquation cracking of cast inconel 738LC superalloy welds", PhD Dissertation, University of Manitoba, Canada, 2005.

 

[2] "Nimonic 75 alloy, Special Metals Corporation". 2014.

 

[3] M. Pouranvari, A. Ekrami & A. Kokabi, "Microstructure development during transient liquid phase bonding of GTD-111 nickel-based superalloy", Journal of alloys and compounds. vol. 461, pp. 641-647, 2008.

 

[4] M. Haafkens & J. Matthey, "A new approach to the weldability of nickel-base As-cast and power metallurgy superalloys", Weld. Journal, vol. 61, pp. 25-30, 1982.

 

[5] M. Abdelfatah & O. Ojo, "On the extension of processing time with increase in temperature during transient-liquid phase bonding", Metallurgical and Materials Transactions A. vol. 40, pp. 377-385, 2009.

 

[6] J. Mattheij, "Role of brazing in repair of superalloy components–advantages and limitations", Materials science and technology. vol. 1, pp. 608-612, 1985.

 

[7] M. Mosallaee, A. Ekrami, K. Ohsasa & K. Matsuura, "Microstructural evolution in the transient-liquid-phase bonding area of IN-738LC/BNi-3/IN-738LC", Metallurgical and Materials Transactions A. vol. 39, pp. 2389-2402, 2008.

 

[8] F. Jalilian, M. Jahazi & R. Drew, "Microstructural evolution during transient liquid phase bonding of Inconel 617 using Ni–Si–B filler metal", Materials Science and Engineering: A. vol. 423, pp. 269-281, 2006.

 

[9] A. Rabinkin, "Brazing with (NiCoCr)–B–Si amorphous brazing filler metals: alloys, processing, joint structure, properties, applications", Science and Technology of Welding & Joining, vol. 9, pp. 181-199, 2004.

 

[10] D. Duvall, W. Owczarski & D. Paulonis, "TLP bonding: a new method for joining heat resistant alloys", Pratt and Whitney Aircraft, Middletown, CO. 1974.

 

[11] T. Shinmura, K. Ohsasa & T. Narita, "Isothermal Solidification Behavior During the Transient Liquid Phase Bonding Process of Nickel Using Binary Filler Metals". vol. 42, pp. 292-297, 2001.

 

[12] W. MacDonald & T. Eagar, "Transient liquid phase bonding processes", The Metal Science of Joining, pp. 93-100. 1992.

 

[13] W. Gale and D. Butts, "Transient liquid phase bonding", Science and Technology of Welding & Joining, vol. 9, pp. 283-300, 2004.

 

[14] M. Pouranvari, A. Ekrami & A. Kokabi, "Solidification and solid state phenomena during TLP bonding of IN718 superalloy using Ni–Si–B ternary filler alloy", Journal of Alloys and Compounds, vol. 563, pp. 143-149, 2013.

 

[15] M. Pouranvari, A. Ekrami & A. Kokabi, "Phase transformations during diffusion brazing of IN718/Ni-Cr-B/IN718", Materials Science and Technology, vol. 29, pp. 980-984, 2013.

 

[16] W. Gale & E. Wallach, "Microstructural development in transient liquid-phase bonding", Metallurgical Transactions A, vol. 22, pp. 2451-2457, 1991.

 

[17] "Alloy Phase Diagrams", 10 ed. ASM Handbook. Vol. 3, ASM International, 1992.

 

[18] P. Sung & D. Poirier, "Liquid-solid partition ratios in nickel-base alloys", Metallurgical and Materials Transactions A, vol. 30, pp. 2173-2181, 1999.

 

[19] A. Bondar, "B-Cr-Ni (Boron-Chromium-Nickel)", Non-Ferrous Metal Ternary Systems. Selected Soldering and Brazing Systems: Phase Diagrams, Crystallographic and Thermodynamic Data.

 

[20] K. Ohsasa, T. Narita & T. Shinmura, "Numerical modeling of the transient liquid phase bonding process of Ni using Ni-B-Cr ternary filler metal", Journal of phase equilibria, vol. 20, pp. 199-206, 1999.

 

[21] O. Ojo, N. Richards & M. Chaturvedi, "Isothermal solidification during transient liquid phase bonding of Inconel 738 superalloy", Science and Technology of Welding & Joining, vol. 9, pp. 532-540, 2004.

 

[22] W. Li, T. Jin, X. Sun, Y. Guo, H. Guan & Z. Hu, "Study of Ni–Cr–Co–W–Mo–B interlayer alloy and its bonding behaviour for a Ni-base single crystal superalloy", Scripta materialia, vol. 48, pp. 1283-1288, 2003.

 

[23] J. Liu, T. Jin, N. Zhao, Z. Wang, X. F. Sun, H. R. Guan & Z. Q. Hu. Effect of temperature on formation of borides in TLP joint of a kind of nickel-base single crystal superalloy. in Materials science forum, 2007.

 

[24] O. Ojo, N. Richards & M. Charturvedi, "Effect of gap size and process parameters on diffusion brazing of Inconel 738", Science and Technology of Welding & Joining. vol. 9, pp. 209-220, 2004.

 

[25] M. Pouranvari, A. Ekrami & A. Kokabi, "Microstructure–properties relationship of TLP-bonded GTD-111 nickel-base superalloy", Materials Science and Engineering: A. vol. 490, pp. 229-234, 2008.

 

[26] M. Pouranvari, A. Ekrami & A. Kokabi, "Diffusion induced isothermal solidification during transient liquid phase bonding of cast IN718 superalloy", Canadian Metallurgical Quarterly. vol. 53, pp. 38-46, 2014.

[1] O. A. Ojo, "On liquation cracking of cast inconel 738LC superalloy welds", PhD Dissertation, University of Manitoba, Canada, 2005.

 

[2] "Nimonic 75 alloy, Special Metals Corporation". 2014.

 

[3] M. Pouranvari, A. Ekrami & A. Kokabi, "Microstructure development during transient liquid phase bonding of GTD-111 nickel-based superalloy", Journal of alloys and compounds. vol. 461, pp. 641-647, 2008.

 

[4] M. Haafkens & J. Matthey, "A new approach to the weldability of nickel-base As-cast and power metallurgy superalloys", Weld. Journal, vol. 61, pp. 25-30, 1982.

 

[5] M. Abdelfatah & O. Ojo, "On the extension of processing time with increase in temperature during transient-liquid phase bonding", Metallurgical and Materials Transactions A. vol. 40, pp. 377-385, 2009.

 

[6] J. Mattheij, "Role of brazing in repair of superalloy components–advantages and limitations", Materials science and technology. vol. 1, pp. 608-612, 1985.

 

[7] M. Mosallaee, A. Ekrami, K. Ohsasa & K. Matsuura, "Microstructural evolution in the transient-liquid-phase bonding area of IN-738LC/BNi-3/IN-738LC", Metallurgical and Materials Transactions A. vol. 39, pp. 2389-2402, 2008.

 

[8] F. Jalilian, M. Jahazi & R. Drew, "Microstructural evolution during transient liquid phase bonding of Inconel 617 using Ni–Si–B filler metal", Materials Science and Engineering: A. vol. 423, pp. 269-281, 2006.

 

[9] A. Rabinkin, "Brazing with (NiCoCr)–B–Si amorphous brazing filler metals: alloys, processing, joint structure, properties, applications", Science and Technology of Welding & Joining, vol. 9, pp. 181-199, 2004.

 

[10] D. Duvall, W. Owczarski & D. Paulonis, "TLP bonding: a new method for joining heat resistant alloys", Pratt and Whitney Aircraft, Middletown, CO. 1974.

 

[11] T. Shinmura, K. Ohsasa & T. Narita, "Isothermal Solidification Behavior During the Transient Liquid Phase Bonding Process of Nickel Using Binary Filler Metals". vol. 42, pp. 292-297, 2001.

 

[12] W. MacDonald & T. Eagar, "Transient liquid phase bonding processes", The Metal Science of Joining, pp. 93-100. 1992.

 

[13] W. Gale and D. Butts, "Transient liquid phase bonding", Science and Technology of Welding & Joining, vol. 9, pp. 283-300, 2004.

 

[14] M. Pouranvari, A. Ekrami & A. Kokabi, "Solidification and solid state phenomena during TLP bonding of IN718 superalloy using Ni–Si–B ternary filler alloy", Journal of Alloys and Compounds, vol. 563, pp. 143-149, 2013.

 

[15] M. Pouranvari, A. Ekrami & A. Kokabi, "Phase transformations during diffusion brazing of IN718/Ni-Cr-B/IN718", Materials Science and Technology, vol. 29, pp. 980-984, 2013.

 

[16] W. Gale & E. Wallach, "Microstructural development in transient liquid-phase bonding", Metallurgical Transactions A, vol. 22, pp. 2451-2457, 1991.

 

[17] "Alloy Phase Diagrams", 10 ed. ASM Handbook. Vol. 3, ASM International, 1992.

 

[18] P. Sung & D. Poirier, "Liquid-solid partition ratios in nickel-base alloys", Metallurgical and Materials Transactions A, vol. 30, pp. 2173-2181, 1999.

 

[19] A. Bondar, "B-Cr-Ni (Boron-Chromium-Nickel)", Non-Ferrous Metal Ternary Systems. Selected Soldering and Brazing Systems: Phase Diagrams, Crystallographic and Thermodynamic Data.

 

[20] K. Ohsasa, T. Narita & T. Shinmura, "Numerical modeling of the transient liquid phase bonding process of Ni using Ni-B-Cr ternary filler metal", Journal of phase equilibria, vol. 20, pp. 199-206, 1999.

 

[21] O. Ojo, N. Richards & M. Chaturvedi, "Isothermal solidification during transient liquid phase bonding of Inconel 738 superalloy", Science and Technology of Welding & Joining, vol. 9, pp. 532-540, 2004.

 

[22] W. Li, T. Jin, X. Sun, Y. Guo, H. Guan & Z. Hu, "Study of Ni–Cr–Co–W–Mo–B interlayer alloy and its bonding behaviour for a Ni-base single crystal superalloy", Scripta materialia, vol. 48, pp. 1283-1288, 2003.

 

[23] J. Liu, T. Jin, N. Zhao, Z. Wang, X. F. Sun, H. R. Guan & Z. Q. Hu. Effect of temperature on formation of borides in TLP joint of a kind of nickel-base single crystal superalloy. in Materials science forum, 2007.

 

[24] O. Ojo, N. Richards & M. Charturvedi, "Effect of gap size and process parameters on diffusion brazing of Inconel 738", Science and Technology of Welding & Joining. vol. 9, pp. 209-220, 2004.

 

[25] M. Pouranvari, A. Ekrami & A. Kokabi, "Microstructure–properties relationship of TLP-bonded GTD-111 nickel-base superalloy", Materials Science and Engineering: A. vol. 490, pp. 229-234, 2008.

 

[26] M. Pouranvari, A. Ekrami & A. Kokabi, "Diffusion induced isothermal solidification during transient liquid phase bonding of cast IN718 superalloy", Canadian Metallurgical Quarterly. vol. 53, pp. 38-46, 2014.

 

[27] M. Arafin, M. Medraj, D. Turner & P. Bocher, "Transient liquid phase bonding of Inconel 718 and Inconel 625 with BNi-2: Modeling and experimental investigations", Materials Science and Engineering: A, vol. 447, pp. 125-133, 2007.

 

[28] I. Tuah-Poku, M. Dollar & T. Massalski, "A study of the transient liquid phase bonding process applied to a Ag/Cu/Ag sandwich joint", Metallurgical Transactions A, vol. 19, pp. 675-686, 1988.

 

[29] Y. NAKAO, K. Nishimoto, K. Shinozaki & C. Kang, "Theoretical research on transient liquid insert metal diffusion bonding of nickel base alloys", Transactions of the Japan Welding Society, vol. 20, pp. 60-65, 1989.

 

[30] Y. Zhou, "Analytical modeling of isothermal solidification during transient liquid phase (TLP) bonding", Journal of Materials Science Letters, vol. 20, pp. 841-844, 2001.

 

[31] M. Pouranvari, "Isothermal solidification during transient liquid-phase bonding of GTD-111/Ni-Si-B/GTD-111", Materiali in tehnologije. vol. 48, pp. 113-118, 2014.

 

[32] Y. Zhou, W. Gale & T. North, "Modelling of transient liquid phase bonding", International Materials Reviews. vol. 40, pp. 181-196, 1995.