Analytical and Numerical Evaluation of Wire Flat Rolling Process Based on the Slab Method and DEFORM-3D

Journal of Advanced Materials and Processing

دوره 8، شماره 4، بهمن 2020، صفحه 3-16   

نوع مقاله: Research Paper

نویسندگان

Behzad Pasoudeh^{* 1}؛ Hadi tagimalek²

¹PhD Student, Department of Engineering, Mechanical group, Urmia University, Urmia, Iran

²PhD Student, Faculty of Mechanical Engineering, Semnan University, Semnan, Iran

چکیده

Considering slab method, a three-dimensional analytical model was adopted to evaluate the rolling pressure, force and torque in symmetrical wire flat rolling. Due to the effectiveness of the shear friction model to express the frictional state in the bulk metal forming, thus, it was used to define in slab formulation. In this paper, the plains strain condition no longer is valid and, the strain on z direction must also be taken into account in calculations. The resultant differential equations were solved numerically by Rung Kutta method and MATLAB software. It was concluded that as shear factor rises in the range of o.4

کلیدواژه‌ها

Wire flat rolling؛ Slab method؛ Rolling pressure؛ Simulation؛ Symmetrical

مراجع

[1]               H. Tagimalek, M. Azargoman, M.R. Maraki, M. Mahmoodi, “The effects of diffusion depth and heat-affected zone in NE-GMAW process on SUH 310S steel using an image processing method”, Inter Jour of Iron & Steel Society of Iran., Vol. 17, Issue. 1, No. 1, 2020, pp. 11-20.

[2]               M. Kazeminezhad, A. Karimi Taheri, “A theoretical and experimental investigation on wire flat rolling process using deformation pattern”, J. Mater. Des., Vol. 26, 2008, pp. 99–103.

[3]               B. Pasoodeh, A. Parvizi, H. Akbari, “Effects of asymmetrical rolling process on the micro hardness and microstructure of brass wire”, JCAMECH., Vol. 49, 2018, pp. 143-148.

[4]               B. Pasoodeh, A. Parvizi, H. Akbari, “Investigation of microstructure and mechanical properties in asymmetrically rolled copper wire”, Journal of the Brazilian Society of Mechanical Science and Engineering., Vol. 30(30), 2017, pp. 5109-5116.  

[5]               A. Parvizi, B. Pasoodeh, K.Abrinia, H. Akbari, “Analysis of curvature and width of the contact area in asymmetrical rolling of wire”, Journal of Manufacturing Process., Vol. 20, 2017, pp. 245-249.

[6]               M. Kazeminezhad, A. Karimi Taheri, “An experimental investigation on the deformation behavior during wire flat rolling process”, J. Mater. Process. Technol., Vol. 160, 2005, pp. 313-320.

[7]               M. Kazeminezhad, A. Karimi Taheri, “Deformation inhomogeneity in flattened copper wire”, J. Mater. Des., Vol. 28, 2007, pp. 2047-2053.

[8]               PP. Gudur, M. Salunkhe, U.S. Dixit, “A theoretical study on the application of asymmetric rolling for the estimation of friction”, Int. J. Mech. Sci., Vol. 50, 2008, pp. 315-327.

[9]               T. Yong, G. Yan-hui, ZD. Wang, GD. Wang, “Analysis of rolling pressure in asymmetrical rolling process by slab method”, J. Iron. Steel. Res. Int., Vol. 16(4), 2009, pp. 22-26.

[10]           D. Kumar, U.S. Dixit, “A slab method study of strain hardening and friction effects in cold foil rolling process”, J. Mater. Process. Technol., Vol. 171, 2006, pp. 331-340.

[11]           S. Chen, H. Liu, Y. Peng, J. Sun, “Slab analysis of large cylindrical shell rolling considering mixed friction”, Int. J. Mech. Sci. Technol., Vol. 30, 2014, pp. 4753-4760.

[12]           M. Qwamizadeh, M. Kadkhodaei, M. Salimi, “Asymmetrical rolling analysis of bonded two-layer sheets and evaluation of outgoing curvature”, Int. J. Adv. Manuf. Technol., Vol. 73, 2014, pp. 521-533.

[13]           S.H. Zhang, D.W. Zhao, C.R. Gao, G.D. Wang, “Analysis of asymmetrical sheet rolling by slab method”, Int. J. Mech. Sci., Vol. 65, 2012, pp. 168-176.

[14]           F. Afrouz, A. Parvizi, “An analytical model of asymmetric rolling of unbounded clad sheets with shear effects”, Journal of Manuf Process., Vol. 20, 2016, pp. 162-171.

[15]           G.Y. Tzou, M.N. Hang, “Study on minimum thickness for asymmetrical hot-and-cold PV rolling of sheet considering constant shear friction”, J. Mater. Process. Technol., Vol. 119(3), 2001, pp. 229-233.

[16]           G.Y. Tzou, “Relationship between frictional coefficient and frictional factor in asymmetrical sheet rolling”, J. Mater. Process. Technol., Vol. 86, 1999, pp. 271-277.

[17]           R, Iankov, “Finite element simulation of profile rolling wire”, J. Mater. Process. Technol., Vol.142, 2003, pp. 355-361.

[18]           A. Parvizi, B. Pasoodeh, K. Abrinia, H. Akbari, “Analysis of curvature and width of the contact area in asymmetrical rolling of wire”, Journal of Manufacturing Processes., Vol. 20, 2015, pp. 245-249.

[19]           S.P. Hamidpour, A. Parvizi, A. Seyyed Nosrati, “Upper bound analysis of wire flat rolling with experimental and FEM verification”, Meccanica., Vol. 54, 2019, pp. 2247-2261.

[20]           M. Kazeminezhad, A. Karimi Taheri, “Calculation of rolling pressure distribution and force in wire flat rolling process”, J. Mater. Process. Technol., Vol. 171, 2006, pp. 253-258.

[21]           A. Parvizi, B. Pasoodeh, K. Abrinia, “An analytical approach to asymmetrical wire rolling process with finite element verification”, Int. J. Adv. Manuf. Technol., Vol. 82, 2015, pp. 1-9.