A Parametric Study of Evaluation of Damage into Solid Dielectrics due to PD Activity using a Kinetic Model

Majlesi Journal of Electrical Engineering

مقاله 7، دوره 8، شماره 3، آذر 2014، صفحه 49-66   

نوع مقاله: Review Article

نویسنده

Alireza Ganjovi^*

Photonics Research Institute, Institute of Science and High Technology and Environmental Sciences, Graduate University of Advanced Technology, Kerman, Iran.

چکیده

A kinetic model based on Particle in Cell - Monte Carlo Collision (PIC-MCC) model is used for parametric study of the damage due to partial discharges activity into the surroundings dielectrics of a narrow channel encapsulated within the volume of a dielectric material. The parameters studied are applied electric field, channel dimensions and gas pressure. After application of an electric field across a dielectric material which contains a narrow channel, repeated ionization process starts in the gaseous medium of narrow channel. Charged particles, especially electrons, gain energy from the electric field across narrow channel and cause damage into dielectric surfaces of narrow channel on impact. The dependence of the electron energy distribution function (EEDF) on the applied electric field is studied. These estimations are performed based on the number of C-H bond-scissions produced by the impacting electrons of a single PD pulse. Based on this technique, the consequent damage into the solid dielectric and the time required to increase surface conductivity is computed. The formation of acid molecules due to interaction of PD pulse with polymer surface in presence of air and humidity causes changes in the surface conductivity of the surrounding dielectrics of the narrow channels. It is observed that the extent of damage caused by a PD is primarily determined by the total number of impacting electrons capable of producing bond-scission at the dielectric. Parameters that effectively cause an increase in the number of energetic electrons increase effective damage as well as surface conductivity of surrounding dielectrics. 

کلیدواژه‌ها

Partial discharges؛ en؛ Dielectric degradation؛ PIC-MCC simulation؛ Parametric Investigation

مراجع

[1] C., Hudon, R., Bartnikas, “Surface conductivity and gas phase reactions arising with epoxy exposed to partial discharges”, IEEE CEIDP, pp. 725-34, 1992.

[2] C., Hudon, R., Bartnikas and M.R., Wertheimer, “Spark-to-glow discharge transition due to increased surface conductivity on epoxy resin specimens”, IEEE TDEI, Vol.28, No.1, pp. 1-8, 1993.

[3] C., Hudon, R., Bartnikas and M.R., Wertheimer, “Effect of hysic-chemical degradation of epoxy resin on partial discharge behavior”, IEEE TDEI, Vol.2, No.6, pp. 1083-1094, 1995.

[4] C., Hudon, R., Bartnikas and M.R., Wertheimer, “Surface conductivity of epoxy specimens subjected to partial discharges”, IEEE International Symposium on Electrical Insulation, Toronto, Canada, pp. 3-6, 1990.

[5] C., Hudon, R., Bartnikas and M.R., Wertheimer, “Chemical and physical degradation effects on epoxy surfaces exposed to partial discharges”, 4th International Conference on Properties and Applications of Dielectric Materials, Brisbane Australia, pp. 811-814, 1994.

[6] P.H.F., Morshuis , F.H., Kreuger, “Transition from streamer to Townsend mechanisms in dielectric voids”, J. Phys. D: Appl. Phys., Vol.23, pp. 1562-1568, 1990.

[7] T., Ishida, Y., Mizuno, M., Nagao and M., Kosaki, “Computer aided partial discharge analyzing system for detection of swarming pulsive microdischarges”, IEE Conference Publication, No. 378, pp. 99-100, 1993.

[8] C., Mayoux, G., Garcia and J., Sarlaboux, “Interaction of corona with dielectric material until damage”, IEEE TEI, Vol. EI-17, No.2, pp. 156-162, 1982.

[9] E.J., McMahon, J.R., Perkins, “Surface and volume phenomena in dielectric breakdown of polyethylene”, IEEE TPAS, Vol.82, No.69, pp. 1128-1136, 1963.

[10] D., Briggs, C.R., Kendall, A.R., Blythe and A.B., Wootton, “Electrical discharge treatment of polypropylene film”, Polymer, Vol. 24, pp. 47-52, 1983.

[11] D., Briggs , C.R., Kendall, “Derivation of discharge-treated LDPE: an extension of XPS analysis and a probe of specific interactions in adhesion”, Int. J. Adhesion and Adhesive, pp. 13-17, 1982.

[12] D., Briggs, D.G., Rance, C.R., Kendall and A.R., Blythe, “Surface modification of poly (ethylene terephthalate) by electrical discharge treatment”, Polymer, Vol. 21, pp. 895-900, 1980.

[13] D., Briggs , C.R., Kendall, “Chemical basis of adhesion to electrical discharge treated polyethylene”, Polymer, Vol. 20, pp.1053-1054, 1979.

[14] A.R., Blythe, D., Briggs, C.R., Kendall, D.G., Rance and V.J.I., Ziehy, “Surface modification of polyethylene by electrical discharge treatment and the mechanism of autoadhesion”, Polymer, Vol. 19, pp. 1273-1278, 1978.

[15] M., Gamez-Garcia, R., Bartnikas and M.R., Wertheimer, “Synthesis reactions involving XLPE subjected to partial discharges”, IEEE TEI, Vol.EI-22, No.2, pp. 199-205, 1987.

[16] E.C., Rogers, E.B., Grad, and V.G., Harriss, “A servo-mechanism for the study of self-extinction of gaseous discharges in cavities in dielectrics”, J. Sci. Instrum., Vol.33, pp. 7-10, 1956.

[17] T., Tanaka, Y., Ikeda, “Internal discharges in polyethylene with an artificial cavity”, IEEE TPAS, Vol. PAS-90, No. 6, pp. 2692-2702, 1971.

[18] D.W., Auckland, S.M.F., Kabir and B.R., Varlow, “Charge deposition in gas filled channels with insulating walls”, IEE proceedings-A, Vol.140, No.6, pp. 509-516, 1993.

[19] S., Serra, G.C., Montanari, and Mazzanti, “Theory of inception mechanism and growth of defect-induced damage in polyethylene cable insulation”, J. Appl. Phys., Vol.98, pp. 034102-1-15, 2005.

[20] G., Mazzanti, G.C., Montanari and F., Civenni, “Model of inception and growth of damage from microvoids in polyethylene-based materials for HVDC cables part 1: theoretical approach”, IEEE TDEI, Vol.14, No.5, pp. 1242-1254, 2007.

[21] G., Mazzanti, G.C., Montanari and F., Civenni, “Model of inception and growth of damage from microvoids in polyethylene-based materials for HVDC cables part 2: parametric investigation and data fitting”, IEEE TDEI, Vol.14, No.5, pp. 1255-1263, 2007.

[22] L.A., Dissado, G., Mazzanti and G.C., Montanari, “Propagation of electrical tree structures in solid polymeric insulation”, IEEE TDEI, Vol.4, No.5, pp. 496-596, 1997.

[23] J.P., Novak , R., Bartnikas, “Ionization and excitation behavior in a micro-cavity”, TDEI, Vol.2, No.5, pp. 724-728, 1995.

[24] A.A., Ganjovi, N., Gupta and G.R.G., Raju, “A kinetic model of a PD pulse within voids of sub-millimeter dimensions”, IEEE TDEI, Vol.16, No.6, pp. 1743-1754, 2009.

[25] V., Vahedi , G., DiPeso, “Simultaneous Potential and Circuit Solution for Two-Dimensional Bounded Plasma Simulation Codes”, J. Comput. Phys., Vol.131, pp. 149-163, 1997.

[26] V., Vahedi, , C.K., Birdsall, M.A., Lieberman, G., DiPeso, and T.D., Rognlien, “Verification of frequency scaling laws for capacitive radio-frequency discharges using two-dimensional simulations”, Phys. Fluids B, Vol.5, pp. 2719-2729, 1993.

[27] W., S. Lawson, “Particle simulation of bounded 1D plasma systems”, J. Comput. Phys., Vol.80, pp. 253-276, 1989.

[28] G.G., Raju, “Gaseous Electronics: Theory and Practice, Boca Raton”,. FL: Taylor and Francis, 2005.

[29] C.K., Birdsall, “Particle-in-cell charged-particle simulations, plus Monte Carlo collisions with neutral atoms, PIC–MCC”, IEEE Trans. Plasma Sci., Vol.19, pp. 65–85, 1995.

[30] V., Vahedi, , M., Surendra, “Monte-Carlo collision model for particle-in-cell method: application to argon and oxygen discharges”, Comput. Phys. Commun., Vol.87, pp. 179–98, 1995.

[31] C., K. Birdsall , A.B., Langdon, “Plasma physics via computer simulation”, McGraw-Hill, New York, 1985.

[32] A., Roldan, J., M. Perez, A., Williart, F., Blanco, and G., Garcia, “Energy deposition model for low-energy electrons (10-10 000 eV) in air”, J. Appl. Phys., Vol.95, No.10, pp. 5865-5870, 2004.

[33] W., Zhang, T.S., Fisher, and S.V., Garimella, “Simulation of ion generation and breakdown in atmospheric air”, J. Appl. Phys., Vol.96, pp. 6066-6072, 2004.

[34] P.J., Mardahl, , K.L., Cartwright, “Reducing numerical heating in 1-D PIC simulations”, Annual Progress Report for 1993, Plasma Theory and Simulation Group, University of California Technical Memorandum, Electronics Research Laboratory, Berkeley, 1993.

[35] P.J., Mardahl , J.P., Verboncoeur, “Charge conservation in electromagnetic PIC codes; spectral comparison of Boris/DADI and Langdon-Marder methods”, Comp. Phys. Comm., Vol.106, pp. 219-229, 1997.

[36] J.P., Verboncoeur, “Symmetric spline weighting for charge and current density in particle simulation”, Journal of Comput. Phys., Vol.174, pp. 421-427, 1997.

[37] L.A., Dissado, G., Mazzanti, G.C., Montanari, “The role of trapped space charges in the electrical aging of insulating materials”, IEEE TDEI, Vol.4, No.5, pp. 496-596, 1997.

[38] S., Prasad, T., Grover and S., Basu, “Coarse-Grained molecular dynamics simulation of cross-linking of DGEBA epoxy resin and estimation of the adhesive strength”, unpublished.

[39] N., Shimizu, C., Laurent, “Electrical tree initiation”, IEEE TDEI, Vol. 5, No. 5, pp. 651-659, 1998.

[40] K.D., Wolter, J., Tanaka, and J.F., Johnson, “A study of the gaseous degradation products of corona-exposed polyethylene”, IEEE TET, Vol. E1-17, No.3, pp. 248-252, 1982.

[41] P.H.F., Morshuis , F.H., Kreuger, “The spatial distribution and electrical parameters of partial discharges in polyethylene insulation during aging”, Proc. 4th Int. Conf. Cond. Breakd. Solid Diel., Sestri Levante/Italy, pp. 209-214, 1992.

[42] R., Bartnikas, “Some observations on the character of corona discharges in short gap spaces”, IEEE TEI, Vol.6, No. 2, pp. 63-75, 1971.

[43] R., Bartnikas, “Engineering Dielectrics”, Vol. I, Corona Measurement and Interpretation, SlT669, ASTM, Philadelphia, 1979.

[44] R. Bartnikas, “Discharge rate and energy loss in helium at low frequencies”, Electrical Engineering, Vol. 52, pp. 348-359, 1969.

[45] R. Bartnikas, “Note on ac discharges between metallic-dielectric electrodes in helium”, J. Appl. Phys., Vol. 40, pp. 1974-1976, 1969.

[46] J.P., Novak, R., Bartnikas, “Quantitative model of a short-gap breakdown in air”, XVIIth International symposium on discharge and electrical insulation in vacuum, Berkeley, pp. 60-64, U.S., 1996.

[47] K., Kaminaga, T., Suzuki, T., Uozumi, T., Haga, N., Yasuda and T., Fukui, “The mechanism of degradation of polyethylene in a high electrical field”, Conference on Electrical Insulation and Dielectric Phenomena, pp. 666-71, 1993.

[48] D.W., Auckland, A.B., Borishade, and R., Cooper, “The breakdown characteristics of air-filled tubules in solid insulation”. IEEE Conference Publication No. 129, Dielectric Materials, Measurements and Applications, Cambridge pp. 15-18, July 1975.

[49] D.W., Auckland, A.B., Borishade, and R., Cooper, “Photographic investigation of breakdown of composite insulation”. Proc. IEE, Vol.124, No.12, pp. 1263-1266, 1977.

[50] K., Wu, Y., Suzuoki, T., Mizutani and H., Xie, “Model for partial discharges associated with treeing breakdown: I. PDs in tree channels”, J. Phys. D: Appl. Phys., Vol. 33, pp.1197–1201, 2000.

[51] W.Y., Gu, C., Laurent, and C., Mayoux, “Characteristics of discharges inside simulated tree micro-cavities under impulse voltage”, J. Phys. D: Appl. Phys., Vol.19, pp. 2197-2207, 1986.

[52] P.H.F., Morshuis and F.H., Kreuger, “Transition from streamer to Townsend mechanisms in dielectric voids”, J. Phys. D: Appl. Phys., Vol. 23, pp. 1562-1568, 1990.

[53] P., Morshuis, “Assessment of dielectric degradation by ultrawide-band PD detection”, IEEE TDEI, Vol.2, No. 5, pp. 744-760, 1995.

[54] C., Mayoux , C., Laurent, “Contribution of partial discharges to electrical breakdown of solid insulating materials”, IEEE TDEI, Vol.2, No.4, pp. 641-652, 1995.

[55] R.J., Densley, “An investigation into the growth of electrical trees in XLPE cable insulation”, IEEE TEI, Vol. EI-14, No.3, 1979.

[56] K., Wu, Y., Suzuoki, T., Mizutani and H., Xie, “Model for partial discharges associated with treeing breakdown: II. Tree growth affected by PDs”, J. Phys. D: Appl. Phys., Vol.33, pp.1202–1208, 2000.

[57] R.J., Densley, R., Bartnikas and B., Bernstien, “Multiple stress aging of solid-dielectric extruded dry-cured insulation systems for power transmission cables”, IEEE TPD, Vol.9, No.1, pp. 559-571, 1994.

[58] H.J., Wintle, “Schottky injection currents in insulators: the effect of space charge on the time dependence”, IEEE TEI, Vol. 12, No. 6, pp. 424-428, 1977.