Design and Development of Automatic Magnetic Setup for Hybrid Single-Point Diamond Turning of Optical Components

Majlesi Journal of Electrical Engineering

مقاله 2، دوره 17، شماره 2، شهریور 2023، صفحه 13-21   

نوع مقاله: Reseach Article

شناسه دیجیتال (DOI): 10.30486/mjee.2023.1970273.0

نویسندگان

Shahrokh Hatefi^* ؛ Khaled Abou-El-Hossein

Ultra-High Precision Manufacturing Laboratory, Department of Mechatronics Engineering, Nelson Mandela University, Port Elizabeth, South Africa.

چکیده

Single-Point Diamond Turning (SPDT) has been widely used in manufacturing of optical components for critical applications including military, defense, aerospace, computer science, electronics, medical, and dental. Magnetic Field (MF) assistance is a recent non-conventional assistive technique that could be used during SPDT process to improve the machining conditions. Recent experimental studies show that using MF assisted SPDT technique can improve the optical surface roughness compared to purely mechanical SPDT process. There are a few studies conducted on the application of magnetic manipulation technique during the SPDT process. The effects of applying a strong MF during diamond cutting on the outcome of the machining process, as well as the optimum MF parameters to be used in SPDT process, are not fully discovered yet. The purpose of this research is to design and develop an automatic MF assistance system that could be used in non-conventional MF assisted and hybrid SPDT processes. The proposed automatic system is capable of communicating with the hybrid controller and precisely set/modify the desired magnetic parameters, including the generated magnetic flux density, at the cutting zone. By using the proposed system, an automatic MF assistance system in non-conventional SPDT processes could be enabled and the optimum machining conditions could be determined.

کلیدواژه‌ها

Linear Control System؛ Magnetic Field Assisted Machining؛ Non-Conventional Machining؛ Advanced Manufacturing؛ Ultra-Precision Manufacturing

سایر فایل های مرتبط با مقاله

2-4865.pdf

مراجع

• [1] Balasubramaniam, R., R.V. Sarepaka, and S. Subbiah, Diamond turn machining: Theory and practice. 2017: CRC Press.
• [2] Hatefi, S. and K. Abou-El-Hossein, "Review of single-point diamond turning process in terms of ultra-precision optical surface roughness". The International Journal of Advanced Manufacturing Technology, 2020. 106(5): p. 2167-2187.
• [3] Gupta, K., Advanced Manufacturing Technologies. 2017: Springer.
• [4] Hatefi, S. and K. Abou-El-Hossein, "Review of magnetic-assisted single-point diamond turning for ultra-high-precision optical component manufacturing". The International Journal of Advanced Manufacturing Technology, 2022. 120(3): p. 1591-1607.
• [5] Chavoshi, S.Z. and X. Luo, "Hybrid micro-machining processes: A review". Precision Engineering, 2015. 41: p. 1-23.
• [6] Li, Z., et al., "Review of diamond-cutting ferrous metals". The International Journal of Advanced Manufacturing Technology, 2013. 68(5-8): p. 1717-1731.
• [7] Hatefi, S. and K. Abou-El-Hossein, "Review of hybrid methods and advanced technologies for in-process metrology in ultra-high-precision single-point diamond turning". The International Journal of Advanced Manufacturing Technology, 2020. 111(1): p. 427-447.
• [8] Hatefi, S. and K. Abou-El-Hossein, "Review of non-conventional technologies for assisting ultra-precision single-point diamond turning". The International Journal of Advanced Manufacturing Technology, 2020. 111(9): p. 2667-2685.
• [9] Bhowmik, S. and D. Zindani, "Overview of Hybrid Micro-manufacturing Processes", in Hybrid Micro-Machining Processes. 2019, Springer. p. 1-12.
• [10] Lauwers, B., et al., "Hybrid processes in manufacturing". CIRP Annals, 2014. 63(2): p. 561-583.
• [11] Peruri, S.R. and P.K. Chaganti, "A review of magnetic-assisted machining processes". Journal of the Brazilian Society of Mechanical Sciences and Engineering, 2019. 41(10): p. 450.
• [12] Philip, J., P. Shima, and B. Raj, "Enhancement of thermal conductivity in magnetite based nanofluid due to chainlike structures". Applied physics letters, 2007. 91(20): p. 203108.
• [13] Philip, J., P. Shima, and B. Raj," Evidence for enhanced thermal conduction through percolating structures in nanofluids". Nanotechnology, 2008. 19(30): p. 305706.
• [14] Yeo, S., M. Murali, and H. Cheah, "Magnetic field assisted micro electro-discharge machining". Journal of Micromechanics and Microengineering, 2004. 14(11): p. 1526.
• [15] Sodano, H.A. and J.-S. Bae, "Eddy current damping in structures". Shock and Vibration Digest, 2004. 36(6): p. 469.
• [16] Sodano, H.A., et al., "Improved concept and model of eddy current damper". Journal of Vibration and Acoustics, 2006. 128(3): p. 294-302.
• [17] Liu, C., K. Jiang, and Y. Zhang, "Design and use of an eddy current retarder in an automobile". International Journal of Automotive Technology, 2011. 12(4): p. 611-616.
• [18] Hatefi, S. and K. Abou-El-Hossein, "Feasibility Study on Design and Development of a Hybrid Controller for Ultra-Precision Single-Point Diamond Turning". Majlesi Journal of Electrical Engineering, 2019. 13(2): p. 121-128.
• [19] Hatefi, S. and K. Abou-El-Hossein, "Design and Development of High-Precision Hybrid Controller for Ultra-Precision Non-Conventional Single-Point Diamond Turning Processes". Majlesi Journal of Electrical Engineering, 2020. 14(2): p. 61-70.
• [20] Hatefi, S., O. Ghahraei, and B. Bahraminejad, "Design and Development of a Novel Multi-Axis Automatic Controller for Improving Accuracy in CNC Applications". Majlesi Journal of Electrical Engineering, 2017. 11(1): p. 19.
• [21] Hatefi, S., O. Ghahraei, and B. Bahraminejad, "Design and Development of a Novel CNC Controller for Improving Machining Speed". Majlesi Journal of Electrical Engineering, 2016. 10(1).
• [22] Coey, J.M.D., Rare-earth iron permanent magnets. 1996: Oxford University Press.
• [23] Bendjedia, M., et al., "Position control of a sensorless stepper motor". IEEE Transactions on Power Electronics, 27(2): p. 578-587.