Study of Fatigue Behavior and Microstructure of 1.6582 Steel Joint by Resistance Butt Welding

Journal of Environmental Friendly Materials

مقاله 6، دوره 7، شماره 1 - شماره پیاپی 13، شهریور 2023، صفحه 35-40   

نوع مقاله: Original Article

نویسندگان

O Ashkani¹؛ H .M Semnani¹؛ H Sabet²؛ M .R Tavighi²

¹Faculty of Technology and Engineering, Science and Research Branch, Islamic Azad University, Tehran, Iran

²Department of Materials Engineering, Karaj Branch, Islamic Azad University, Karaj, Iran

چکیده

Various fusion welding methods can be used to create a successful jont. However, with the increase in the thickness, fusion welding processes have limitations. Therefore, solid-state welding methods have been developed and in the meantime Resistance Butt Welding method has been chosen as a suitable method. In this study, joining of 1.6582 alloy steel has been investigated and analyzed, and the effect of the electric current parameter has been investigated in this welding method especially on Fatigue parameter. The results have shown this method is suitable for connecting (Joining) parts with symmetrical geometry. Also results shown that increasing the current to an optimum current leads to increasing the strength, As a result, the fatigue properties increase similarly to the strength. The noteworthy point here is that at stresses less than 220 MPa, the mentioned sample has a fatigue limit after welding, and this joint can be useful in various industries, including tool making.

کلیدواژه‌ها

Resistance Butt Welding (RBW)؛ 1.6582 Steel؛ Fatigue behavior؛ Solid state

مراجع

[1] R. R. Baracaldo, M. C. Santos and M. A. Acosta Echeverría, Scientia Et Technica, Technological University of Pereira (UTP), Vol. 23, No. 1, 2018, pp. 51.

[2] N. F. H. Kerstens and I. M. Richardson, J. Mater. Process. Technol., Vol. 209, Aug. (2009), pp 2715.

[3] V. Lebedev, S. Kuchuk and V. Krivenko Yatsenko. "Resistance Flash Butt Welding of Pipelines." (1980).‏

[4] K. B. Min, K. S. Kim and S. S Kang, J. Mater. Process. Technol., Vol. 101, No. 1–3, 14, Jan. (2000), pp 186.

[5] C. L. Jenney and A. O’Brien, “Welding Handbook and Welding Science and Technology”, Miami (USA), (1991), pp. 36, 50.

[6] S. Gaddam, R. S. Haridas, C. Sanabria, D. Tammana, D. Berman and R. S. Mishra, Mater. Des., 221 (2022): 110949.‏

[7] R. R. Baracaldo, M. C. Santos and M. A. Acosta Echeverría, Scientia et Technica 23.1 (2018): 51.‏

[8] R. W. Messler J. R. “Principles of welding, Process, Physics, Chemistry and Metallurgy”, 1st edition, Boston, 210. (1999): pp. 150.

[9] N. H. F. Kerestens, “Investigation and Control of Factors Influencing Resistance Upset Butt Welding”, Ph.D. thesis, TU Delft University, Netherlands, 2010.

[10] M. Kabasawa, New Technol. Resistance Weld. Process., Vol. 56, 1987, pp. 155-161,

[11] Kuroda, Toshio, Kenji Ikeuchi, and Hyuma Ikeda. "Flash butt resistance welding for duplex stainless steels." Vacuum 80.11-12 (2006): 1331.

[12] D. Leroy Olson, T. A. Siewert and S. Liu, Glen R. Edwards, “ASM Handbook, Welding, Brazing and Soldering”, USA, 2004.

[13] F. Quan Chen , Zu Wei Lin, and Guo Wei Liang, Adv. Mater. Res.. Vol. 201-203. Trans Tech Publicat. Ltd, (2011), 2661.

[14] Eman El Shrief, Abla El-Megharbel, Aly El Domiaty and Hassan Abd El-Hafez1, Manuf. Rev. 8 (2021): 19.‏

[15] M. Sharifitabar, A. Halvaee, Mater. Des., Vol. 31,(2010),pp.3044.

[16] M. Sharifitabar, A. Halvaee, S. Khorshahian, Mater. Des., Vol. 32, (2011), pp. 3854.

DOI: 10.1016/j.matdes.2011.03.007

[17] Muksin R. Harahap, A. Bakhori, S. Napid, M. Rafiq Yanhar and A. Hasibuan, Int. J. Eng. Technol., 7(2), April (2018): 389.

[18] William E. Luecke, J. D. McColskey, Ch. N. McCowan, Stephen W. Banovic, R. J. Fields, Timothy Foecke, Thomas A. Siewert and Frank W. Gayle, Technol. Admin., US (DOC), (2005).‏

[19] A. Karimi, M. Adeli and M. Soltanieh, J. Manuf. Process., 77 (2022): 551.‏

[20] Muksin R. Harahap, A. Bakhori, S. Napid, M. Rafiq Yanhar and A. Hasibuan, Int. J. Eng. Technol., (UAE) (2018).

[21] EN 10027-2: 2015; Designation Systems for Steels-Part 2: Numerical System. CEN: Brussels, Belgium, (2015).

[22] A. N. Abddlssalam, Thermomechanical processing of 34CrNiMo6 steel for Large Scale Forging, (2014) Sheffield, UK, uk.bl.ethos. 628590.

[23] ASM Int. the Mater. Information Society-ASM International,2018

[24]. M. Abiri, M. Movahedi, A. Ozlati, the 21st national conference on welding and inspection, and the 10th Conf. Natl. Inst. Non-Destructive Testing, Isfahan, (2019) (in Persian).

[25]. O. Ashkani, A. Abbasi, H. R. N. D. Monfared, The microstructure and mechanical properties of the non-homogeneous Joint of austenitic stainless steel 304 to 316 made to resistance butt welding, the 19th National Conference on Welding and Inspection and the 8th Natl. Conf. on Non-Destructive Testing, Esfahan, 2017 (in Persian).

[26] Triyono, Jamasri, M. N. Ilman and R. Soekrisno, Modern Appl. Sci. 6.5 (2012): 34.‏

[27] A. Pasarkar, A. Mane, N. Singh, A. Datarkar and Nilesh Raut, Rev. Res. Eng. Struct. Mater., 9(1): (2023); 181.