A DC-DC Converter for Electric Vehicle Application

Majlesi Journal of Electrical Engineering

مقاله 2، دوره 18، شماره 4، اسفند 2024، صفحه 1-10   

نوع مقاله: Reseach Article

شناسه دیجیتال (DOI): 10.57647/j.mjee.2024.1804.51

نویسندگان

Bogaraj Thirumalaisamy^{* 1}؛ Sweety Jose Paul²؛ Natarajan Angappan²؛ Karthikeyan Subramanian²

¹Professor, Department of Electrical and Electronics Engineering, PSG College of Technology, Coimbatore-641004, Tamil Nadu, India

²Department of Electrical and Electronics Engineering, PSG College of Technology, Coimbatore, India.

چکیده

An innovative Synchronous Buck Converter (SBC) with a wide input voltage range is presented in this article for use in Electric Vehicle (EV) applications. The disadvantages of higher losses in an Asynchronous Buck Converter (ABC) are intended to be addressed by the Synchronous Buck Converter. Fewer losses occur in the circuit when MOSFET (or any controlled switch) is used in place of diode. To enhance system performance, the control approach known as Emulated Peak Current Mode (EPCM) is employed. The design of a broad range input SBC and the investigation of power loss calculations using different control techniques, which are implemented using PSIM, are the primary contributions made in this paper. The buck converter employed in this paper has an output voltage of 12 V and a wider input voltage range of 40–75 V. It is utilized by electric vehicles' light and horn systems. Using PSIM software, the SBC using the EPCM, Current Mode Control (CMC), and Voltage Mode Control (VMC) techniques is simulated. Hardware results coincide with the simulation results and thus the results are validated.

کلیدواژه‌ها

Electric Vehicle (EV)؛ Emulated Peak Current Mode (EPCM)؛ Drain to Source resistance (RDS)؛ DC-DC converter؛ Current Mode Control (CMC)؛ Voltage Mode Control (VMC)

مراجع

1. Sweety, P., Subha Hency, P., Wessley, G., & Rajalakshmy, P. (2021, December 2). Environmental Impact of Electric Vehicles. In E-Mobility (pp. 31–42). Springer International Publishing. https://doi.org/10.1007/978-3-030-85424-9_2
2. Azizi, I., & Radjeai, H. (2015, December). A bidirectional DC-DC converter fed DC motor for electric vehicle application. 2015 4th International Conference on Electrical Engineering (ICEE). https://doi.org/10.1109/intee.2015.7416683
3. Chen, G., Deng, Y., Dong, J., Hu, Y., Jiang, L., & He, X. (2017, July). Integrated Multiple-Output Synchronous Buck Converter for Electric Vehicle Power Supply. IEEE Transactions on Vehicular Technology, 66(7), 5752–5761. https://doi.org/10.1109/tvt.2016.2633068
4. Del Moral, D. L., Barrado, A., Sanz, M., Zumel, P., Raga, C., Lazaro, A., & Miniguano, H. (2015, June). Improvement of the Synchronous Buck converter dynamic performance applied to Hybrid Electric Vehicle regenerative power systems. 2015 9th International Conference on Compatibility and Power Electronics (CPE).
5. Uddin, M. R., Tasneem, Z., Annie, S. I., & Salim, K. M. (2017, February). A high capacity synchronous buck converter for highly efficient and lightweight charger of electric easy bikes. 2017 International Conference on Electrical, Computer and Communication Engineering (ECCE). https://doi.org/10.1109/ecace.2017.7912936
6. Hwu, K. I., Shieh, J. J., & Jiang, W. Z. (2018, May). Analysis and design of type 3 compensator for the buck converter based on PSIM. 2018 13th IEEE Conference on Industrial Electronics and Applications (ICIEA). https://doi.org/10.1109/iciea.2018.8397859
7. Hegazy, O., Van Mierlo, J., & Lataire, P. (2011, May). Design and control of bidirectional DC/AC and DC/DC converters for plug-in hybrid electric vehicles. 2011 International Conference on Power Engineering, Energy and Electrical Drives. https://doi.org/10.1109/powereng.2011.6036530
8. Sweety, P., Geetha, M., Kanakaraj, J., & Abinaya, C. (2017, June). Power Quality Improvement by Direct Power Control of Active Front End Rectifier. Journal of Scientific and Industrial Research (JSIR), 76(6), 339–342. http://nopr.niscpr.res.in/handle/123456789/42065
9. Farhani, S., & Bacha, F. (2018, March). Modeling and control of a dc-dc resonant converter interfacing fuel cell in electric vehicle. 2018 9th International Renewable Energy Congress (IREC). https://doi.org/10.1109/irec.2018.8362507
10. Sweety, P., & Muthulakshmi, M. (2021, December). Vienna Rectifier for Electric Vehicle Charging Station. International Journal of Mechanical Engineering, 6(3), 511–516. https://kalaharijournals.com/resources/IJME2021Dec41-60/DEC_47.pdf
11. Cui, S., He, D., Chen, Z., & Habetler, T. G. (2012, March). A wide input voltage range ZVS isolated bidirectional DC-DC converter for ultra-capacitor application in hybrid and electric vehicles. 2012 IEEE International Electric Vehicle Conference. https://doi.org/10.1109/ievc.2012.6183239
12. Singha, A. K., Kapat, S., & Pal, J. (2016, September). A robust design framework for stable digital peak current-mode control under uniform sampling. 2016 IEEE Energy Conversion Congress and Exposition (ECCE). https://doi.org/10.1109/ecce.2016.7854769
13. Jiang, W. Z., Lai, J. S., & Hwu, K. I. (2018, May). Digital compensator design for high-frequency hybrid resonant buck converter. 2018 7th International Symposium on Next Generation Electronics (ISNE). https://doi.org/10.1109/isne.2018.8394706
14. Choi, J. M., Byen, B. J., Lee, Y. J., Han, D. H., Kho, H. S., & Choe, G. H. (2012, November). Design of Leakage Inductance in Resonant DC-DC Converter for Electric Vehicle Charger. IEEE Transactions on Magnetics, 48(11), 4417–4420. https://doi.org/10.1109/tmag.2012.2196027
15. Santhi, M., Rajaram, R., & Raj, I. G. C. (2006, December). A ZVCS LC-Resonant Push-Pull Power Converter Circuit for Battery-Fuel Cell Hybrid Systems. 2006 IEEE Conference on Electric and Hybrid Vehicles. https://doi.org/10.1109/icehv.2006.352288