An Investigation on the Modeling of Heat Distribution and Atomic Diffusion in the Joining of the AA2024-T4 to AA6061-T6 by TLP Process

Journal of Environmental Friendly Materials

مقاله 4، دوره 4، شماره 2 - شماره پیاپی 8، اسفند 2020، صفحه 21-25   

نوع مقاله: Original Article

نویسندگان

Anbarzadeh A¹؛ Sabet H²؛ Geranmayeh A. R¹

¹Department of Materials Engineering, South Tehran Branch, Islamic Azad University, Tehran, Iran

²Department of Materials Engineering, Karaj Branch, Islamic Azad University, Karaj, Iran

چکیده

The simulation of heat distribution has long been applied for estimating optimal time for heat treatment process in an attempt to optimize the energy consumption. Aluminum alloys have been used to achieve appropriate strength-to-weight ratio and reduce the fuel consumption. In the present research, heat distribution modeling was performed for joining AA2024-T4 to AA6061-T6 in the TLP process utilizing MATALAB R2016b. For this purpose, thermal properties and density of the base alloys and the clamp were extracted from respective ASM standards and applied in the coding. Finally, 1D, and 2D simulations were run to simulate the heat distribution over the base metal at the process temperature. Moreover, the time required to have the copper diffused into the interlayer was estimated through the simulations. The diffusion depth of the Sn into the base metal (Al) was further modeled at different points in time. A Sn-2.5Bi interlayer with two different thicknesses (50 and 70 microns) was also evaluated through actual experiments.

کلیدواژه‌ها

TLP؛ Modeling by MATLAB؛ AA2024-T4؛ Heat Distribution؛ Atomic Diffusion

مراجع

[1] Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate (Metric) ASTM- Designation: B209M-14-2014.

[2] Aerospace Specification Metals Inc (ASM). ASM Mater. Data Sheet-800 398-4345. Aluminum 2024-O.1987.

[3] Aerospace Specification Metals Inc (ASM). ASM Material Data Sheet- 800 398-4345. Aluminum 6061-O. 1987.

[4] A. Alhazaa, T. I. Khan, I. Haq, Mater. Charact., 61 (2010) 312.

[5] Aerospace Specification Metals Inc (ASM). ASM Mater. Data Sheet-800, 398-4345. Aluminum 2024-T4. (1987).

[6] A. N. Alhazaa, T. I. Khan, J. Alloys Compd. 496 (2010) 351.

[7] M. S. Kenevisi, S. M. Mousavi Khoie. Mater. Lett., 76, (2012), 144.

[8] M. S. Kenevisi, S. M. Mousavi Khoie, (TLP) Bonded Joint. Mater. Design., 38 (2012) 19.

[9] M. Samavatian, A. Halvaee, A. A. Amadeh, A. Khodabandeh, Mater. Charact., 98, (2014), 113.

[10] M. Samavatian, A. Halvaee, A. A. Amadeh, A. Khodabandeh, T. Nonferr Metal Soc. 25 (2015) 770.

[11] A. Anbarzadeh, H. Sabet, M. Abbasi, Joint. Mater. Latt., 178, (2016), 280.

[12] Hugh Baker, Alloy Phase Diagrams. ASM Handbook, ASM International. (1992)

[13] Aerospace Specification Metals Inc (ASM). ASM Material Data Sheet-800, 398-4345. Aluminum 6061-T6. (1987).

[14] C. H. Ma, R. A. Swalin, Tin. Acta. Metallurgica., 8, (1960) 388.

[15] H. Y. Zhao, J. H. Liu, Z. L. Li, Y. X. Zhao, H. W. Niu, X. G. Song, H. J. Dong, Process. Mater. Latt., 186, (2017), 283.

[16] G. Erdelyi, K. Freitag, H. Mehrer, Diffus. Tin Implanted in Aluminum. Philosophicmaal Gazine., 63, (1991), 1167.

[17] Aerospace Specification Metals Inc (ASM). ASM Mater. Data Sheet-800 398-4345. AISI 4130 Steel, normalized at 870^oC (1600^oF). (1987)